Hardware Controllers: Joysticks/Yokes | Throttle Quads | Rudder Pedals | Drivers etc

I am in need of an internal wiring diagram of the CH Products Pro Pedals. One of the wires involved in the differential breaking for the right side pedal has come loose and I can't see where it is supposed to be attached. If no diagram is available and someone with these pedals is willing to have a look inside, the wire in question is a small gauge black wire that is connected to the large white plug on the right side of the circuit board as you are facing it. I need to know where to connect the free end of this wire. Any help is much appreciated. Doug

Hey all, so I would love to get that TM Boeing yoke but my desk is thicker than the clamp can handle. Any ideas out there as to how I could get it to work on my desk (it’s about 2.5 inches thick), or if anyone else has had this problems? Thank you for your time! mb

Hi, have the prodesksim crj throttle package. Has anyone found a profile or know how to get the fuel lock levers to work? Have to move them in P3D and then move them on the throttle, which seems to defeat the object! Have contacted prodesksim, but not very helpful-advised me to search youtube, but cant find any help on there either!

Could anyone please tell me what are the default sensitivity settings for the TCA Sidestick Airbus Edition are in MSFS 2024? I changed them by mistake when I adjusted them for the CRJ v2 and now need to reset the settings back to default in MSFS 2024.

Maybe it's common knowledge that some modern mice can do this but I bought a new mouse (after 10y!) and one of its buttons changes the rate so you can set it right where it feels just right in-sim. It is a fairly cheap wired mouse from Logitech w/ a couple of assignable buttons as well as this acceleration affecting button depending on how many times you press it changes the rate so panning is much nicer now. Logitech G403 Hero 25K

My Honeycomb Bravo, which I've had for a couple of years, has been problematic at best. None of the lights have ever worked, binding settings with FS2024 is a real challenge, but the biggest disappointment is the trim wheel, which works only sporadically, and sometimes not at all....until today! For some reason, when I selected the Pilatus jet (PC-24, I think) I found that the trim wheel worked almost perfectly--and I have no idea why. What a treat it is to be able to fly along and properly trim the plane out. I don't even need to use autopilot all the time...you just trim it out and it cruises along smoothly with only occasional small inputs to the trim wheel and yok…

Anyone have any experience with these? I’ve got a set on order because I love turboprops. I also like to fly PMDG planes as well…any issues/advice getting this set up? Thanks

I pre-ordered this on opening day for it back in mid-January. Wanted to let those that did, that I finally got the email to pay, and it will be shipping. Finally! This should be timed perfectly for the upcoming PMDG 777ER and the all-new sound package for all the 777's. This will pair nicely with their Boeing MCP that has already shipped to me. Got all from the Global site, the regional sites are way too long a wait.

Hi everyone, this is my first post as I am only into this wonderful hobby for the last 3 weeks or so. I am having trouble getting my Thrustmaster TFRP pedals to work properly. The brakes work as they should, as does the right-hand pedal, but while the left-hand pedal has full physical travel, in the aircraft, it only shows about 25% of movement. I have tried to calibrate them in MSFS but no matter what I do, the left-hand pedal does not work properly. When I try and calibrate them in Windows 11, though they show up in "Game Controller", all I get is a joystick calibration tool that is not relevant for pedals (it is asking me to push buttons and to rotate the controll…

https://fselite.net/content/continued-confusion-over-honeycomb-aeronautical-management-and-charlie-rudder-pedals/ "....the Serial Number contains a factory identifier, which at the time of writing reads “SA” on the authentic product and “RY” on the unauthorized product.” I recently purchased these pedals and sure enough the S/N contains the "RY". I need to reach out to MyPilot storel to see if I have any recourse with them as the official company, Snakebyte, won't be providing any support. And I doubt that any support would be available from whoever made them. The "counterfeit" ones are working ok but I'm concerned if anything goes wrong.

Does anyone have this HOTAS working well in MSFS24' ?, If so, please tell me how, seems impossible so far.

I just need a little help.. I seem to loose the calibration settings during a flight, I believe it's the Quadrant unit itself, everything sets up ok in the USB game controller and the FBW A320 EFB, but I do have to calibrate the quadrant unit each time that I fly. Take off, climb and cruise all seems to be ok until I start to descent and then I will loose the calibration on the unit, ether on one of the throttles or flaps, speed brakes, they also show out of sink on the cockpit pedestal....my question is, how or where is the calibration settings stored for the quadrant unit, any help would be greatly appreciated..

Supposed to come in 2025. There could be a tariff war breaking out and raising prices in about a month (China-USA).

I have a problem to install throttles from TCA captains pack x, after I have deleting them in Flightsimulator 2020. I have tried many times with different ways, but the throttles will not move at all or are stopping higher than idle. Hope anyone can help me solve this problem. Keld Mogensen SAS264

As the title suggests - I am thinking of upgrading my current rudder pedals to something more realistic/immersive. I currently use TM T.Flight Rudder Pedals which gets the job done but when it comes to MSFS/2024, pedals seems ted more sensitive. Plus I have been using these pedals since I ever started flight simming some 7/8 years go but it is about time to upgrade these. I'm considering Thrustmaster's TPR Pendular Rudder Pedals, but these are 5x more expensive then the ones I currently have. What do you people think as well as if you own TPR pedals, what is your feedback?

Looks interesting. I wonder how much better it could be if the sim supports Force Feedback. Would love to see it get to this level..

looks very potential... https://youtu.be/PmzxdR-l_HM?si=M8hhx9-NQswmCcu4

Has anyone have setting to get the Logitech Extreme 3D Pro working in FS 24' ?, or any advice at all to get it usable ?

Has anyone tried the javasimulation's MCDU hardware. The site seems a bit unprofessional with text like "Lorem ipsum dolor sit amet," on there. I'm trying to see if they are a legit company, but I can't find much information about them. They are selling the MCDU for $420 USD which is a lot cheaper than other offerings that I've seen.

Hi, The Saitek/Logitech ProFlight Yoke 90 to 180 conversion kit is complete. If you are interested, here is the YouTube video link: Thanks for watching.

Hey guys, So despite their product page saying word for word "Streaming Display Mode displays PFP 3N (Panel of Flight Plan) data of any 737 aircraft from any game or professional simulation software running on the Windows platform", this is not the case. It does not work with any other 737 model other than the PMDG 737-800 (according to chat support). I'm unfamiliar with the WinWing software, is there a way to program it so we can make it work? Similar to Spad.next?

Hi All I'm having issue using Saitek's Flight Multi Panel. The numbers I choose in FSX show wrong numbers in the FMP. Ditto using the panel for the ALT and VS. Results do not match in FSX. Help! Thanks Phil

Glad to find the solution to the 180 degree of rotational angle design in Hall Effect Sensor application for Saitek Cessna Flight Yoke after many trials and errors. Here is the video to show the installation of HE kit for both Roll (180 degree ) and Pitch (85 degree) sensor units which will replace the faulty Saitek OEM potentiometers in my good old 15 years Saitek Cessna Yoke. Thanks for watching. Here is the video link: https://youtube/7-Sg9LqhNdA

Hello, My controller AXAIR is no longer recognized by FSUIPC6, whatever USB I use on the computer. While checking the FSUIPC6.ini file, I noticed that there are twice the same reference and I suspect that it is the origin of the problem. Could you confirm? [JoyNames] AutoAssignLetters=Yes A=Saitek Pro Flight X-55 Rhino Throttle A.GUID={E94396F0-E721-11EB-8004-444553540000} E=Saitek Pro Flight X-55 Rhino Stick E.GUID={E942D3A0-E721-11EB-8002-444553540000} B=MIAP STD B.GUID={4981D2D0-E40F-11EC-8001-444553540000} C=MIAP STD C.GUID={E942D3A0-E721-11EB-8002-444553540000} D=Saitek Pro Flight X-55 Rhino Stick D.GUID={E9436FE0-E721-11EB-8003-…