PMDG 737NGX | 737NGXu

Was any thought given to supplying alternative models with a lower LOD, or one that contains multiple LODs ? Given that "One" PMDG737 is a stain on most systems, imagine having 2 or more running, as AI or in Multiplayer. Geoff

Schould it look like this? Whats wrong with the lights? Carl

Hi guys, After a dozen or so take off's I have only landed twice, every single time it has been a fatal error, this is the latest Faulting application name: fsx.exe, version: 10.0.61472.0, time stamp: 0x475e17d3Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000Exception code: 0xc0000005Fault offset: 0xffffff3fFaulting process id: 0xdb0Faulting application start time: 0x01cc559c0e67cbb8Faulting application path: D:\Microsoft Flight Simulator X\fsx.exeFaulting module path: unknownReport Id: e324f6e6-c1d2-11e0-b78d-001b2128d6ec Specs in Sig

Hi EveryoneHave had a few little issues with the NGX but in general love it. My question is that the horizon line in the HUD is not on the horizon when looking out into the distance. It is a little above the horizon, any ideas what is likely to be going on?CheersBarra

Well, I thought I would try the 737 NGX, I was fully prepared for a big let down in the frame rate department, but glad to report between 22-36 in the vc on the ground and air, I cannot quite believe it!!! And that is with the sliders at a good level too. Thankyou PMDG for a superb plane. Intel 2 core duo 3.3, 6gb Ram 9800GT GPU and Asus PQ5L.

I am not sure if this would be a part of the freeze issue but this happens to me at any airport, in the air, whenever. When I enter the FSX map for example and click cancel to leave and get back into the flight, the screen turns back and does not respond to any key commands other than ESC key, then I am able to only exit the flight, when I press 'Continue Flight' the screen remains black. If I don't touch the FSX menu at all, I can complete the entire flight without an issue. Jacek Gawecki

Are there any instructions for the FMC and CDU pertaining the flight itself as oppossed to what is in Tutorial 1 or PMDG SETUP or FS ACTIONS? Thank you,Michael Cubine

I purchased the NGX an hour ago and now want to activate it, but I get the following popup twice: "ERROR: Activasion library handle creation failed" Then the Window to Enter the Activasion Code appears, I Enter the Code, and then this message appears again. Any thoughts?

Hi,I see the projection of the HUD disappearing behind the Glareshild. That shouldn't be possible, cause the reflecting visor is in front of the glareshield and so the projection has to be.You see it clearly if you adjust your POV a bit to the right.

Hi i just bout the new NGX and i think is the best addone i have flyed on fsx ever! so PMDG crew really nice jobon this one AWSOME!!!but there is a couple of liveries i miss and i really want like the "737-800 WL Tuifly Nordic" and the "737-800 WL Norwegian Airshuttle 6000th"So i was wondering if its posible go get an paint kit so i can make the liveries myself?

Hey Guys, I noticed another issue that I have never noticed before. This is mostly asthetic, but never the less its still something I noticed. I am taking my 1st night flight tonight, I left KCOS at dusk. I turned on my taxi and landing lights. No part of the ground was showing illuminated from my lights when looking through spot view. I think I saw them from the VC only and not the 2d cockpit. Am I missing something that has been covered?

Hi, I am in the SAS WL 737-800 and have gpdt the coldanddark conf. and everytime i want to change the numbers of passengers it does not give me what i type on the keyboard. for instance i have to type 118 to get 125/174 passengers this must be a fault in the FMC Thanks Michael

Collins AutopilotOn the Collins Autopilot none of the push buttons light up when pressed. However each of the push button switches perform the function as indicated on the annunciator panel on the PFD. This problem does not exist on the Honeywell panel since the push button switches all light up when pressed. Anyone else have this problem? Any ideas? Thanks, Jerry

Hi there,I'm running Windows 7 (32bit) on an iMac (can't run Windows in 64bit mode on this one). My specs are:3,06GHz Intel Core 2 Duo4GB 800MHz DDR2 RAMnVidia GeForce 8800 GS 512MBShould I bother buying this or would you suspect my system would cough too much under the strain of running this add-on? I may not be able to upgrade until around january.Cheers,Hakim Harder

I was wondering under what cicumstances will the electric hydraulic pump get into a overheat situation in a real boeing's plane(i got into that situation in PMDG for quite a lot of times)2. i sometimes can't engage G/S after LOC is active ( i set the ILS frequency and course correcly)what is the problem?thanks, guys

Hey all, Not high on the list or anything, but I wondered if there were supposed to be wipers in the 2D? I always fly in the 2D because I have the worst FS computer on the planet...Anyway, I love the MD-11's 2D wipers so I didn't know if they were supposed to be there or if it was a bug.

OK, i was really prepared for a lot of things but not for checking the oil level in a CFM!!Astonishing, very happy here and track-IR is also ordered!BestHolger Kneib

Since I updated my aircraft cfg files (as per livery post, pinned, above) the small trim values window has stopped appearing when I adjust the trip wheel prior to take off. Now all I can do is read an approximate setting from the dial. Weird. Also the Head up display is out of alignment unless I'm using track IR.

I've gone from 15 fps to 25-30 after deleting all textures, scenery, config folders, etc. Then I went through the usual maintenance of using ccleaner, starting in safe mode then running eusing free registry cleaner and finally mydefrag on the "system disk monthy" setting. I reinstalled FSX with sp1 and 2. I have not reinstalled Acceleration. I have also not yet reinstalled FSUIPC. Then I re-added FPS Limiter, shader 3 mod, let the tweaking tool page make me a new fsx.cfg, and followed the instructions for nvidia inspector here as well as the NGX set up manual. Have I left anything out? Im exhausted. My test was in the vc sitting at the gate, which is where it has been t…

ok i have requested this re-paint several times in repaint topic, but i don't think anyone has noticed....my call how can this repaint be left out MiamiAir is a popular charter operator..please create this repaint or release the paintkit!

Hi boys. I flew PMDG 737 in this weekend, look everything work like real airplane, But when observe the press of PSI to start engines they no come to press need to start, I close the packs L and R open bleed of APU, isolation valves put in auto position. But we don´t get PSI to start engines more the 30PSI. But when I put one in open and other in close we get 30PSI very strange for me because uselly we put close all packs L and R for start. But work fine when I use the external APU, close de bleed in get 35PSI for start the fist engine. Who can help me about this information ? One other information is, when you close de packs with APU and bleed on of APU for start engine …

I've discovered another minor issue with the PMDG 737-900. This is from a screen capture I took 3 minutes ago when I loaded my saved flight from KIAH-KLAS. As you can see, the magenta lines linking the waypoints on the ND have mysteriously vanished and I can't get them to come back... Anyone else experienced this?

<p id="disqus_thread" style="padding-top: 0px; padding-right: 0px; padding-bottom: 0px; padding-left: 0px; margin-top: 0px; margin-right: 0px; margin-bottom: 10px; margin-left: 0px; border-top-width: 0px; border-right-width: 0px; border-bottom-width: 0px; border-left-width: 0px; border-style: initial; border-color: initial; outline-width: 0px; outline-style: initial; outline-color: initial; "> A question for you I have tried to replicate this flight on the angle of attack site made by Chris. I have followed how he sets up his FMC step by step, except I haven't used s takeoff and climb reduction. But on my release version, each time I line insert 200 or FL200 …

Awesome to learn mayday proc. in. Thank you so much PMDG :) Absolute joy to fly :D Now, quickie, how do I top up my oil?

I couldn't see this bug on the issue tracker thread and I know other people have had this problem so I thought I'd post it again.Basically, there are only 2 digits visible on the course and heading displays on the MCP - which makes it pretty hard to select an accurate heading without having to look at the ND! My fsx installation is in the C:// location, I have followed the introduction document and there are no other addons interacting with fsx. I only have REX 2 and one other aircraft installed. If it helps my system specs are:i5 2500kAsus p8p674gb ddr3 1600mhz1GB ATI 5850It would be good to know who else is having this problem! Thanks,