AxisAndOhs Support

Hi Guys, 1st of all a big Thanks to Lorby about this great tool. It helped me a lot to automize/optimize the handling of my aircrafts. Now my topic: I tried to create the Accu /Pressure Indicator gauge of the A320, and it contains 3 pointers. Unfortunately I can't create any offset for the pivot point of the pointer. Do I something wrong, or is it impossible to move the pivot point from the center of the picture or to have more than one pointer in one gauge? Regards lowbudget

Hello @ll, we are currently working on the above mentioned WebFMCs. The first two require data collection from within AAO, so the WebFMCs can only be released after version 4.50 of AAO is out. Release of the 4.50 is scheduled for the end of this week (unless something unexpected happens). The WebFMCs will be a free addon to AAO, as usual.

Hello, I am trying to work with a cockpit dial that has values of 0, 1, 2, 3, and 4. I would like to map two buttons on my HOTAS to either increment the variable by 1, or decrease it by one for each press. So far, I have this code that works to increment the variable correctly with each press, though it does not stop when reaching 4. 0 1 2 3 4 (L:RIO_RADAR_RANGE, Number) 5 seq (>L:RIO_RADAR_RANGE, Number) I have not found a way to decrease the variable after setting it this way. I have tried these also to increase and decrease the variable, but wasn't able to get either to work. (L:RIO_RADAR_RANGE:0, Number) 1 + (>L:RIO_RADAR_RANGE) (L:RIO…

Hey, I'm trying to bind my honeycomb Bravo to the FCU panel with AAO. Using the function watch simulator events in AAO, I noticed that pulling or pushing for example the altitude knob gives following variables: (>IE:AIRLINER_MCU_ALT_PULL) (>IE:AIRLINER_MCU_ALT_PUSH) Pulling the knob with the mouse will make the aircraft go in open descent or climb mode. However, if I use AAO to bind my HC Bravo to these commands, the plane will not go in open descent or climb mode. When I operate the buttons, I can see on my screen that the knob is moving (popping out or in), but that is it. Any chance somebody can assist me with thi…

Hello, I am trying to set up my Honeycomb yoke for the above plane but am struggling with how to do the maneuver roll pitch switch in particular. It is a button that is supposed to be held down while changing the pitch, then released. I turned on the "watch events" feature in AAOs and found the event that is triggered when I press the switch on the yoke and I assigned that event to my own yoke. It seems, though, that once I press my button the sim thinks that switch is being held down; as though it is turned on but I can't turn it off. I know there is the ability to add an event when releasing the button but I can't find an event that turns the maneuver switch off. …

How can I bind the B on the keyboard with the baro button in the Fenix A320? kind regards Alex

Hello, I managed to create 2 buttons to increase and decrease the rate (with SIM_RATE_INC and SIM_RATE_DECR), but I would like a third, a kind of panic button, which would set the rate to 1, with SIM_RATE_SET... I do not see at all how to set it ? Can someone help ? Thank you.

I recently upgraded my MOBO, CPU, and Ram which necessitated an upgrade from Win10 to Win11. After re-installing all of MSFS2020 and AAO (Newest version on Simmarket) on Win11 24H2 I was able to select the Enable Saitek in AAO and it worked fine. I then had to re-install Win11 to downgrade from 24H2 to 24H3 to resolve an audio stutter issue, but I have not been able to select the Enable Saitek since it is greyed out. I have tried unplugging the panel from the USB hub and plugging it in to a direct USB on the I/O panel, then restarting both MSFS and AAO but no joy. I have also tried starting both MSFS and AAO as Admin but no joy. Are there any other tips that you may have …

any way to get the webfmc for the FSLabs airbus ? or is it wasm based and not possible ?

I'm in the process of setting up my controllers with the A320neo from FBW and I've ran into some scripting issues with one of the buttons. It's the CHR button above the landing gear lever. On the mobiflight page (and in debug mode), it says the code should be (>H:A32NX_CHRONO_TOGGLE), but that doesn't do anything. What's the proper way to code this in the scripting editor?

Good Evening All, I have now took on what seems to be a mammoth task of setting up the A320, after getting used to BVars in the Asobo 152 and 172 i thought "it maybe time consuming but how hard can it be" 🙂 that was a mistake haha. I have had a look at "watch sim events" and a lot don't come up at all so i thought ill jump into developer mode and try looking for the BVars in behaviours, a good many of them work as expected when doing the previous profiles but a huge amount dont seem to so i took to flightsim.to to download a profile and have a look see how others have done it. I then got inspired to have a go but ended up rather confused. (I am still very new …

Hello friends, I am finishing my scripts for AAO using the PMDG. I would like to know if anyone has used a variable to obtain the value set for the minimums, as I am working on an automation process. I’ve searched and tried some generic values, but nothing worked so far. Found. Thank you.

Hi, hoping this is the right forum. I have a Stream Deck Plus & XL, and some functions are working in the sim but not all. My setup is: MSFS 2024 Profiles - https://flightsim.to/file/44350/standard-avionics-suite-for-streamdeck-xl AAO 4.51 b09 running and connected to sim (two green lights) Stream Deck Plugin (38.01) G1000 Bridge What works: Most of the AP / nav / radio buttons on the Stream Deck Plus profile (setting radios, heading, altitude, etc) Seemingly almost nothing on the MFD/PFD controls on either the Stream Deck Plus or XL (e.g., MFD softkeys). …

Anyone having AAO issues because FSUIPC is also running? Thanks

Hi guys, I downloaded AAO yesterday and have encountered an issue when binding my VPF Rhino stick base using a Virpil VFX grip for MSFS2020. Hopefully it's just something obvious I'm missing as a new user.. I'm trying to bind the stick's hat switch to the: ROTOR_LATERAL_INC ROTOR_LATERAL_DEC ROTOR_LONGITUDINAL_INC ROTOR_LONGITUDINAL_DEC events. I can create the bindings okay, and with the "Change button assignment" window open AAO recognizes the hat switch (it changes in the "Assigned button/key" field when I move the switch) but after I close that dialogue and go back to the main screen AAO no longer registers pushes from the buttons. …

Hello All. Using the software listed below, with aq generic Autopilot profile in use, I cannot get the LCD panel on the Streamdeck Plus I use to work at all, the LCD panel is BLANK on mine, but the other Autopilot buttons etc are there… The rotary knobs have nothing to control… The same Streamdeck Plus using the same plugins and profiles listed below WORKS FINE on another PC! here’s what I’m using, I think I must be missing something with Lorbys A&O: Streamdeck Plus software vs. 6.8.0 - Firmware 2.0.3.4 Lorbys A&Ohs vs 4.51 b09 for MSFS 2024 In 2024 Community Folder: Mobiflight lorbysi-content-fippanel lorbysi-content-hooks zzz-lo…

Hi I am trying to set up of PMDG 777 Ext Pwr (Prim and SEC) status on X-touch Mini button but it doesn't seem to work. I an using AAO 4.51 Build 09. There are two variables available for power to be ON and AVAIL but neither seems to work. 1. (PMDG:ELEC_annunExtPowr_ON[0]) 2 (PMDG:ELEC_annunExtPowr_AVAIL[0]) When these variables are observed in AAO they don't show any change with changes in Ext Pwr switch positions. Tried to search the internet and Chat GPT as well but to no avail. Kindly help. Thanks

Button Type: Lorbi-SI AxisAndOhs: TextGuage Title: Condition Variable 1: S: MyScripts-Cessna 208B Condition Lever Position Script Title: Cessna 208B Condition Lever Position Script Group: MyScripts RPN SCRIPT (likely wrong): (TURB ENG CONDITION LEVER POSITION:1) 2 == 'HIGH' (TURB ENG CONDITION LEVER POSITION:1) 1 == 'LOW' (TURB ENG CONDITION LEVER POSITION:1) 0 == 'CUTOFF' ? 'UNKNOWN' Basically, just trying to learn how AaO and a very basic script works so I can learn from that and keep going, hopefully. I would like the StreamDeck Button (details above) to display: TURB ENG CONDITION LEVER POSITION:1 = 2 then display HIGH T…

Hello, I'm currently in the process of familiarizing myself with AAO. I have already integrated various Fenix scripts and it works very well. Now I would like to connect the two potentiometers to my Logitech X56 HOTAS with the dimmer of the PFD/ND. There is the template "<UseTemplate Name="FNX32X_Interact_Knob_Increment_Lock_Template"> in the Fenix_Interieur.xml The only question is how do I have to integrate this template/variable into AAO? Thanks for your support 🤩 Holger

I do not seem to get a simple script running using AAO for MSFS 2024. What do I want to achive: I have three different variables ((L:S_OH_ELEC_BAT1, Number), (L:S_OH_ELEC_BAT2, Number) and (A:BRAKE PARKING POSITION, bool)). If all values of them are 1, I would like to call script A and all other cases call script B. But even checking all variable values using the AND-operator does not work: (L:S_OH_ELEC_BAT1, Number) 1 == && (L:S_OH_ELEC_BAT2, Number) 1 == && (A:BRAKE PARKING POSITION, bool) 1 Using the script editor's debug, this expression does not give me any result other than (L:S_OH_ELEC_BAT1, Number) 1 == && (L:S_OH_ELEC_BA…

Hey, not sure if Im missing something, but I cant find the rudder left and right axis in AAO. In the game i can bind the rudder either combined as one axis or seperated as two. Would be nice to have the seperated option in AAO so I can get rid of Universal Control Remapper. Tanks in advance!

Hi, Firstly I want to thank you for introducing me to BVar theybhave made life much easier I'm almost finished with the C-152 profile now and I may share it for others as I have mapped almost every function of the Asobo aircraft so far. I am struggling with a few last functions on the streamdeck all to do with the transponder Firstly I have used a toggle for the identify on the XPDR which works fine but I can't find a variable that works to tell my streamdeck if it's on or off. Secondly I am struggling with the actual transponder dials I have used BVar NAVCOM_Transponder_Code_THOUSANDS_Inc but nothing happens... would you have any a…

Hi, I am new to AAO so please bear with me. I have started to setup a new C172 configuration on MSFS 2020 using AAO instead of MSFS default controller mappings. I have the basics for my Warthog joystick and throttle working well now and the sensitivity difference is much better (I am an ex-private pilot) ;) I have just acquired an X-touch mini for the purposes of controlling my TBM-930 autopilot and radio/van comms. It has been added to my windows 11 PC; I have it working with Ableton Music software separately sending and receiving midi signals. I have been following the setup tutorials on youtube by 'Flight Sim and other stuff' and have the panel setu…

I use the x-touch for the autopilot function for all aircrafts, including the gns 540. Is there a way to copy and paste specific or a batch of "assigned buttons" from one aircraft to another? While lvars or other commands for the autopilot change for each aircrafts, the gns540 do not. It would be great, therefore, to be able to copy and paste all the gns540 button assignments without having to reprogram them for each aircraft. Perhaps there's another method, in which case I'd like to see it.

So Sorry for the 2nd question of the day but This is the last 2 buttons I need to finish the panels page of my C-152 before attempting to learn how to map the radios 😞 (God Help Me) I am having some success with this but it seems to be acting a little strange and I don't know enough about the scripting yet to locate the issue. I am trying to increase the carb heat by 5% at a time with each button press using an event button. (IE:DEICE_ENGINE_1) 0.05 + 1 min (>IE:DEICE_ENGINE_1) This pulls the lever out 5% on the first press as I want it to.... but then on the second press it comes all the way out to 100% Thanks and sorry to be a pain…