EMB505 Phenom 300 HD Series for FSX | P3D

I have installed the GTN Complete program into the Phenom 300 for both FSX Steam and P3DV4.3 and also used Ber'ts Mod and all was well.I also installed into A2A's Bonanza v35 but without Bert's Mod using the A2A's Configuration program.When I go to checklist for the Phenom using the GTN 750 mfd I get an abbreviated Bonanza checklist in both FSXSteam and P3DV4.3! Additionally the Bonanza checklist in P3DV4.3 is abbreviated with note saying" list not finished". Any idea what is wrong? regards Harvardfly. When I checked the GTN Trainer program and select utilities/checklist I see the same abbreviated Bonanza checklist and note "list not finished".

Hi All, I'm under the impression that there are some mods floating around that fix a few things with the 300 (like the avionic master issue) but I've not been able to find them. I'm not looking for any changes to the G1000 as I'm quite happy with it, but if there are some fixes that would be grand. Thanks, James

I had just reinstalled the Phenom 300 and the PFD displays are very dim. When I try to increase the PFD display brightness they do adjust but as soon as I stop they revert to 1%. In the setup menu the 'PFD DSPL' is set to 'Manual' and won't stay set to 'Auto'. The 'MFD DSPL' is set to 'Auto' and doesn't stay set to 'Manual'. The MFD display brightness does adjust properly though, 100% in day time and no brighter then 60% in night time. I had also installed Synthetic Vision. I uninstalled the Phenom 300, Navigraph addon and Synthetic Vision. I rebooted the computer and installed just the Phenom 300 and I still have the same problem. I hoping that I'm missing someth…

Hello I am unable to enter a flight plan because the Departure option is greyed out after selecting Proc. Impossible to enter a Departure.

Hi all, I have this weird problem when trying to enter data into the G1000 of the Phenom 300. When trying to enter a value (e.g. an airport), sometimes (i.e. most of the time), the characters keep changing automatically (rapid scrolling through its list continuously). To stop it, you have to shutdown the plane (batt 1+2=off). I am using P3d v4.1. Note I have already changed my mouse and still same thing. Video can be seen here:

Hello all, I am just doing my first flight YBBN-YSSY using my new Carenado Phenom 300, and new GTN750(Bert Piekes' mod). Using map mode I find there is no access to charts in the charts menu and there are no runways etc on the map. I recall somewhere seeing an option for worldwide Jessperson charts OR North American charts I remember selecting the Jessperson option but I do not have the charts. I now cannot find where I selected that option and am actually wondering if the GTN can access the Australian, or anything other than the North American, charts. Am I destined to wonder lost in Australia or is there a fix for this. Thanks guys Tony

Bert, A heads up I have just sent you a PM regarding the mod for the GTN 750 integration into the Carenado Phenom 300. Thanks Tony

Any one know of or have a Phenom 300 profile for Simbrief? It has a 100 profile but not a 300 that I can find. Thanks

Hi I have Phenom 300 v2.0 installed in P3Dv4.3. Can one install the 2.1 version right over the older version or must the Phenom 300 be deleted before installing the newer version? Any significant improvements from 2.0 to 2.1 or not worth the installing? I have Bert's GTN 750 Mod working in FSX steam. Can I use the same directions to place the GTN 750 in P3DV4.3 or must I request new instructions due to differences? Thanks Jack

Hi Folks. Can anybody please help solve these two problems I'm having with the Carenado Phenom 300. I am running P3Dv4.3. When I load the phenom, I click 'Shift 6' and select Ready to Taxi. I wait for the alignment to complete. When I open the 'Proline Loading Screen' the navigraph just sits at 0 percent, and doesn't download. When I open the FMS and click on Procedures, the airport ICAO does not show in the departure window. I try to type the ICAO in, but the cockpit keypad does not do anything. It is not working. Can someone telll me what I'm doing wrong please. Is it perhaps a faulty install? Thanks John

In both the Phenom 100 and 300 the GPS magenta course indicator in the PFD stays frozen in place when the GTN 750 is installed. Will not point to the next waypoint. If I don't install the 750 and just use the G1000, it works ok. Hate using the G1000 on this plane so I use the 750. Is there anyway to fix this problem? Jim

So, i have this problem where the gear sometimes does not want to retract, the gear lever goes up but the gear stays down and the MFD display still says 3 down green. I have no idea what would be causing the problem, the issue seems occur randomly. Both the gear button on my HOTAS and clicking the lever do nothing. Has anyone else had this problem? Thanks.

Using Gtn 750 with Carenado 300 and Prepar3D v 4. Not being able to save a flight and flight plan with Gtn I pause the flight. After a period of time I resume the flight but the Gtn buttons are no longer active. Another issue I have is upon landing the rudders are not active. I checked failures and there are no failures listed, however if I reset the rudders work again. Any suggestions appreciated.

I just bought the gtn 750 to use with my Carenado 300, but it just recognizes as a 2D panel. anyone knows how to integrate with the virtual cockpit? Thanks you Pedro

I recently purchase the Phenom 300 but when I try to load the plane FSX crashes. Just wondering if anyone else has the same problem.

Hi guys In the after start checklist it gives the correct trim setting dependant on the centre of gravity. For example...CG MAC 19. Gives a flaps 1 trim of 7.7 and a flaps 2 trim of 6.8. My question is how to work out the centre of gravity and what does MAC mean? Cheers Stinger

Certainly not a big issue, but has anyone found a method to turn off the copilot PFD display?? Should certainly be a way, but heck if I can find it... <grin> Thanks, Mike EDIT: Issue resolved,,, power on/off is located just below the mounting screw in the upper left corner of the PFD.

the Traffic "TAS" screen will display targets for AI aircraft but not online aircraft (I fly VATSIM). Has anyone been able to get that and/or Weather radar (I use ASN16) to work with online inputs? I'm using FSX, haven't tested in with P3D yet. thanks Ron N142RW

Hi everybody, I recently took the plunge and purchased the Phenom 300 along with the Navigraph extension and SVN packages. I've got most everything figured out to my satisfaction but the one thing I can't figure out is how to shut off the copilot's PFD. The hot spot just below the upper left mount screw is there but nothing happens when I click it. Has anybody else had this problem? Thanks! Brian System: Windows 10 Home 64-bit Intel Core i7 7700 3.6GHz, 16GB RAM GeForce GTX 1070

How can I tell if the Navigraph updates are working? The files in the CarenadoNavigraph folder are up to date: AIRAC cycle : 1804 Version : 1 Valid (from/to): 29/MAR/2018 - 25/APR/2018 but the opening screen on the G1000 says my charts are out of date? Also when I first loaded the aircraft, the message showed saying the database was updating. No problem there.

Hello, This is an explanation on how to import a flight plan in the G1000. It is easier than you think :-). Phenom 300 Importing a flight plan Regards.

Hi guys, What does the thin red and white dotted line signify when it shows to the right of the green speed tape line. (Not the overspeed line which is above the green line) Some times it shows, sometimes not? Cheers Stinger

http://me2.do/53kglLyS In my MFD there has no fix name(NBD, VOR, Airport etc). I have a trouble at make input a flight plan. For example I don't know where SID & STAR fixes are located in. Just enter inferred input and fixed them again and again. I have a EXTENSION PACK v1.2 (v1.1 is same result. Default navi data has no problem.) To install again but result is same. What did I miss I do? What shoud i do? Sorry for my bad english. Thank you.

Hello, I have bought the Phenom 300 and the navigraph expansion pack. But when I fly with it for more than 2-3 hours, as soon as I touch anything on the G1000, it crashes with a ntdll.dll error. I am sure that this error comes from the Phenom 300 as I never had any crashes for almost a year now with the simulator running for sometimes more than 24 hours straight with complex aircraft like the PMDGs. If you guys could help me to figure this out, I would be very thankful !

Hello, the N1 of my Phenom 300 is only 87%, no matter what I do ... As I do not know how to change the aircraft.cfg I ask the help of the friends, what I did wrong? I must have changed something without wanting to. Could anyone help? Thank you Amauri Penze