The MILVIZ Support Forum

Hi Folks, Just happened to be perusing the support forum over at MilViz and noticed a fairly recent post where Colin mentioned the "possibility" of considering updates for the B55 and C310... "We're potentially going to revamp the 310 and the B55 up to today's standards." Just to be clear - this doesn't appear to be a commitment - but I was wondering if I'm the only one enthusiastic about this prospect ??? The C310 is hands down the BEST light twin out there in my book and a joy to fly... An update would be more than welcome as it's the only light twin I fly... The B55 is almost as good - but - I'm convinced it has a bit of an issue with the FDE that…

I have had the T-38, both the original and now the advanced versions, for a few years now, and I have had the devil's own time flying both of them. Now if I had not flown the real thing for over 100 hours in UPT I would perhaps not be so nonplussed, but either this thing has some serious flight model issues or else (and this is always a possibility!) there is something wrong with my computer or my disk version FSX installation (I had the same problems with it in FSXSE back when I had it installed in both). Now I must confess up front that although I have time in the real airplane, it was all done back in 1972! So I may have forgotten a thing or two over the interve…

Don’t know where to turn. Having a problem with GTN 750 in Milviz Otter in Prepare3Dv4.1. At beginning of flight it works normal. Cockpit mount works and when I choose drop down or stack gtn 750 the cockpit gtn 750 screen goes black as it should. After about a half hour if I use the drop down both screens stay lit with the drop down map frozen but when I use the keys in the drop down it effects the cockpit mounted gtn. The cockpit mount continues to work but I can no longer use the drop downs. I tried changing the cpu core # to 1 but problem persists. This is the only Milviz aircraft I own. Any suggestions appreciated, Thanks.

Have finally got this great bird installed in P3Dv4. Everything seems to be working fine, but I cannot find the avionics switch so I can turn on the default GPS units. I have checked all of the documentation, and have not found mention of it. Can anyone help?

Hi, Not sure if this error is anything to worry about? Apart from this message, the installation appeared to go perfectly normally and the Beaver looks fine in the sim. Haven't flown it much yet though. Thanks in advance, Andy

I am having this same problem with MV_WX.dll after us minutes of flight the p3dv4.1 closes with the error of MV_WX.dll what should I do? I went there no dll.xml and there it is like this: <Name>WXAdvantage</Name> <Disabled>False</Disabled> <Path>Modules\MV_WXM.dll</Path> <DllStartName>module_init</DllStartName> <DllStopName>module_deinit</DllStopName> </Launch.Addon> </SimBase.Document> What should I do ? Thank you

Hey! What are you doing? Are you flying into some nasty weather? Not sure? Check it out with this: http://store.rexdownload.com/advanced-weather-radar-for-fsx-fsx-steam-edition-and-p3d-v25-v323/10-wx-advantage-radar.html

Hi! There is a helpful list of product versions on http://milviz.com/MV-product-list.html. It shows e.g. T-38A - Advanced Series to have a recent update 3.171108, but two days ago I tried another download from sendowl and still got 3.160107 (and now one less available download, but that's not yet a problem). Only then I remembered the MVAMS, and could download the update there. And I have the C310R 170808 from a different shop (realflightshop), while above page lists 171202 as the current version. The MVAMS shows the aircraft, but does not offer the updated version. My questions are: Should the C310R 171202 update be already available from other …

I have the Milviz Otter in P3dv4. I now also have the WX radar updated to P3dv4. I have the WX popup working. I do not have any weather displayed from the WX 3d panel. The panel is completely dead and can not be switched on. If I use the pop up, I get the range display on the 3d panel, but no weather display? Anyone get this working in V4? Regards David

I have the latest version for it in v4.1 All is good until I go to land and when I get slow like 60-70 the elevator gets super twitchy does anyone else have this? Is there a fix/work around? I really want to like this plane but as it is now, wow, it's no go for me I want to get the otter, that looks great but I'm afraid I'll have the same problem.

Hi guys, has anyone an idea how I can draw the attention of the support team of Milviz to my case? I can’t access to the support forums to download the last version of my purchased aircraft because I don’t remember my password and when I use the forgotten password functionality, the email with the password or reset link never arrives (The mail isn’t in the spam folder either). The recovering password function seems to be broken. Since the 2017-11-25 I am trying to get this problem solved. I Received a first email asking me if I can access to the forums and after a few mails telling I can’t access to them (the last email addressed to several members of the Milvi…

I downloaded and installed the C310R in Prepar3D v4.1 yesterday, this is the first airplane Add-on after a reinstall of the flight sim. Have completed a couple of flights and find the C310R very enjoyable, however I seem to be having a small problem with the Fuel flow gauge in so much the needle(s) increase from low to high fuel flow but stay on high for the rest of the flight, no reduction due to change in mixture or power. w7 1080ti gpu I7-4770 cpu o/c 4.4 bob edit note... have noticed the fuel selector gauge has not been turned on however I did retest with it on and got the same result.

Hi- How do you power this thing on? No mention in the docs. Thanks.

I thought I'd group all my questions into one post. First off: MVAMS or ACM? They both configure (mostly the same) settings? Second: En-Route Navigation. I default to 'Ready To Fly' and have also selected Auto Position Update and Auto Waypoint Sequence options. I have watched a YouTube tutorial on the INS; not having much luck here. I can navigate to a VORTAC whose channel I manually input, and that is about it. I don't see a Target 2 position on the INS?? (S Model) Approaches: With the ILS sytem powered on, and a correct frequency set via MVAMS, I get the correct morse identifier and also course deviation needle on the HSI. On my attitude indicator I get g…

Just wondering if I'm the only here but for some reason after a certain amount of time my DHC2 will not work properly and I will have to reinstall it. I purchased the aircraft when it first came out and used it for a while and everything worked great but after not using it then going back and flying it again (months later) no engine gauges work and or oil/cylinder gauges. I'm experiencing the same thing right now, I reinstalled it probably about a month ago and flew it around a few times then I came back to it today and it's doing the same thing. I have not reinstalled P3D (3.4) however I am having issues with the child window problem. Is there a fix or do I just have to…

Hi, i installed the Beaver in my P3Dv4.1 sim, on a separate drive G:\Prepar3D v4 Add-ons\MilViz Beaver By loading the aircraft in the sim there is a error popup which mention the soundfiles "SND1.wav...54?" can't be found. the error is says there is a unknown location. Error Encountered Full Error Code 0x3 Location 5 File G:\PREPAR3D V4 ADD-ONS\MILVIZ BEAVER\SimOjects\Airplanes\DHC-2 Beaver Milviz\panel\MVSounds\SND1.wav ...SND54.wav and indeed, the MVSounds dir don't exist in my G:\Prepar3D v4 Add-ons\MilViz Beaver\SimObjects\Airplanes\DHC-2 Beaver Milviz\panel dir, the SND1.wav (...54) files are located in the G…

I received an email from PCAviator advising that I have a free update to the Milviz Cessna 310. This updates to Version 4.150724. Where do I find the version I have installed now? I looked on the Milviz forum and there is no notification about this update so just wondering what this is all about.

The manifold pressure gauge on the MilViz Beaver doesn't appear to be working. No matter what the throttle setting, the gauge is pegged to 10 in Hg. Also, the prop lever doesn't move. I can still adjust the prop speed using my yoke but the lever in the virtual cockpit doesn't move. I'm currently running version 170829 but had the same thing with my earlier version. Anyone see this also and have any clues?

Hi All- I have recently gotten into flying the Milviz 732 alot more. I bought it when it first came out and barely flew it then. I noticed there are not many repaints for this awesome airplane though. I was wondering if anyone still does them actively? If so... What are the odds of seeing the below Sierra Pacific (The current US based charter company) Ameristar both the cargo one and the pax one. USAir silver body with the red stripes on the blue tail Carnival Airlines Mucho Gracias!!! Spell Dawg

More then a year ago I informed about the status of the KingAir 350i. Despite several promises, assurances etc about a release last year, the KS 350i still isn't finished. Some buyers are waiting for more then 3 years now, with multiple new other aircraft released frequently Any clues what the status will be at the end of this year?

I'm using the GTN 750 in the Beaver, and I've noticed the autopilot NAV function doesn't work while in GPS mode, but it does work fine when I switch over to LOC. Anyone else experience this?

Morning all, Instead of the default Michelin tires and the garish spinning prop for the FG-1D corsair, I did some repaints, If anyone is interested these files can be downloaded here. https://www.dropbox.com/s/8kn0ahlbonczfy9/GPL_MILVIZ_FG-1D_Wheel-Prop_Fix.zip?dl=0 Just unzip the files directly into the texture folder of the airplane you want. e.g. unzip into, texture.GreyGhostVWC Be sure to backup any existing files. George

Hi all, I just purchased the Beaver and installed in P3D v4. I load the default flight (F22). Then I select to load the Beaver, and all I get is a crash to desktop (CTD). Is there anything I can do to fix this? Any idea or suggestion would be very welcome !

Hello, I recently attempted to update the DHC-2. I uninstalled it first as instructed using the "MVAMS" product and selected my P3Dv4 installation. After uninstalling i now have nothing, no request to run again, no shortcut, nothing at all.How am i to reinstall this product? Thanks

Anyone try this bad boy? Looks pretty hefty... Mark