LINDA Support

Hallo LINDA-Freunde, wie schon gepostet funktioniert der AXE über ARCAZE und LINDA sehr gut bei mir, leider will der Mensch immer mehr... Welche Möglichkeit besteht im AXE den Squawk über ein kleines Tastenfeld einzugeben? Es grüsst der airbusheinz

Hallo LINDA-Freunde, habe 6 Joysticks, ARCAZE usw., an LINDA angeschlossen. Es funktioniert prächtig, doch manchmal tritt folgender Fehler auf: ALLE Joysticks werden von LINDA erkannt, ALLE Schaltbefehle usw. werden in LINDA korrekt angezeigt, es funktioniert grundsätzlich! Ein Joystick kommt manchmal aber nicht im Flieger an ? Gibt es Erklärungen? Es grüsst der airbusheinz

Hallo, ich wollte mal fragen wo ich die Zeit einstellen kann nach der Linda automatisch wider in den (z.B.) EFIS Mode 1 zurück kehrt? Also wenn ich ganz rechts oben auf den "Mode Switch" drücke ( "VRI EFIS MODE toggle" nennt der sich ), dann kann ich die zweite Belegung der knöpfe für das EFIS benutzen. Ok, nach einiger Zeit schaltet Linda dann wider auf den EFIS Mode #1 zurück. Kann ich diese Zeit einstellen und wenn ja wo ? Danke Euch !! flusie

Hallo LINDA-Freunde, seit Wochen arbeite ich nun schon mit LINDA, mein Cockpit läuft super... Heute überascht mich LINDA mit der Erroemeldung "Invalid pointer operation" ? Meine Joysticks werden nicht erkannt ?! Gruss airbusheinz

Hello I don't know if its possible but is there any apps out there that can monitor actions from with in FSX and pass to linda in order to synchronize the connected devices through Linda EG A third party copilot say Fs2crew pushes Vnav as commanded by the pilot using voice command for example from within the virtual cockpit in the PMDG 737NGX so there fore the Virtual MCP in the NGX now does not match what's currently set on the VRinsight MCP2 boing IE according to the MCP2 VNAV is off but its been switched on from the virtual cockpit by the copilot. Is there anything that may ensure they are in synch both ways Regards Wayne

Hello! I am trying to program my Mcp combo2 with some funtions. For example I have a plane with RXP 430. I managed in other plane (P51 civ) to manage the 430 gps rxp with the combo.. but that was because the lua file was modified. In a default plane with RXP.. I cannot... and have to copy the p51 lua file to the new one to make work some functions (like magnetos, generators, battery switches.. etc). The thing is that seems that the lua file let the funcions, even if they are internal, work for the profile.. and if there is no lua file then they won't work. My question is (even for the working P51-A2A civ) How I can make for example the zoom in out with th…

Hallo LINDA-Freunde, "guenseli" hat mich gebeten nach Fertigstellung ein paar Bilder einzustellen... ARCAZE und LINDA arbeiten perfekt, das Fliegen ohne Maus und Tastatur hat schon was... Was leider noch nicht funktioniert ist das Auslesen der Daten über FSUIPC für die 7-Segmentanzeigen. Trotz vieler hilfreicher Beiträge in diesem Forum will mir dies noch nicht gelingen ?! Es grüsst der airbusheinz

Hi all, Is there a way to make a 'click' sound via an lua command? I have a script that throws a switch and I would like it to click when it does it.

Hello, I like to combine some actions for some planes. I want to put more then on Action on a button press. I guess I have to use if - then - else. But all my tries will not work. Does anybody can show me please an example for such a scipt? Kind Regards Tom

Hope someone can help, I use LINDA with my MCP and it works great. The problem I have is setting buttons on my Saitek throttle. When I assign a button for example, " fuel cutoff" to button 15. I save settings, a message comes on screen to tell me config is saved. I test with LINDA open and works great. When I close LINDA, the button then does not work. If I program a button on the MCP to do the same, it works ok. Any ideas would be fantastic.

What I like to know is if it is possible to use the commands which are LUA scripted in LINDA can be used in FSUIPC for switching through keystroke or other hardware which is not listed in LINDA? Example: FSUIPC mouse macros I can use via FSUIPC on a GoFlight Switch panel, is there any possibillity that I bring Commands from the linda lua scipt to goflight? Cheers Tom

Please forgive me if this question is answered deep within this forum... Can LINDA be loaded on a second computer (not main FSX computer) and work with WideFS? Thanks in advance. Henry S.

Hi guys, this isnt a request, I was curious as to whether you will support Prepar3d in the future?? Your config would work great on that sim.

Hi, I have some problems with my new MCP II. The aircraft is the standard Boeing 737-800 (FSX): - EFIS has no standard commands (ARP, WPT, DATA etc.) GPS commands (with Ident GPS) works fine - MCP works fine - radio works fine Linda console shows : EFIS mode command I : empty command for ARPT Linda settings-page = 3 x green Can somebody help me to locate the cause of this failure? Greetings, Jos Kroese The Netherlands

Hi, does Linda is compatible with VRi MCP-II (Airbus) panel ? I would like to use my VRI Panel with the 747 PMDG. Do you think it will work ? thank you

Hallo Freunde, gestern war die Welt noch in Ordnung... LINDA geht beim Drücken von FSX sync immer auf "FSX Default" ? Eigentlich sollte "Aerosoft Airbus X" erscheinen ? Was mache ich falsch ?? airbusheinz HAT SICH ERLEDIGT! FEHLER GEFUNDEN!

I have the Ifly original and the MCP combo. always work good with Linda, but yesterday i upgrade the ifly in the site of Flight1 for the version 3.1. After that the MCP combo just accept a few functions already by default. On EFIS just the BARO work, on MCP only the knobs and the COM is good except the buttons above this. I try program the buttons and the knobs but nothing happen. After this i install the LINDA 1.11 and still the same. Anyone can help on this? Thanks

Hi, I would like to use the GNS Libary inside LINDA. As far as I can see, it uses keypresses with "STRG+ALT" e.g. The problem is, whenever I use the ALT-Button, the FSX Menu opens. How can I avoid this by using the predefined key set? Regards, pero

Hallo LINDA-Spezialisten, für den AXE versuche ich die FLAPS zu "programmieren". Der "Guenseli" hat dies toll für den ND_RANGE und ND_MODE gemacht, es funktioniert tadellos! Als Anfänger habe ich aber Probleme... Im Anhang meine Editor Einträge. Nach der Zuordnung in LINDA erhalte ich beim Betätigen des entsprechenden Hebels eine Fehlermeldung, die FLAPS werden auch nicht gesetzt !? Für Hilfe dankt der airbusheinz

MCP Combo 2 with RealAir Beech Duke, Win 7, 64 bit, and Linda (no other VRinsight software) The Duke fuel valves are maddening....using the mouse to open too often causes the view to jump to some other part of the plane. So,,,,I opened the Tracer and followed the instructions . The outcome was/is that opening and closing the fuel valves is an FSX command: FUEL_SELECTION_2_ALL IS 66517 TO open AND 65955 for both to close. I then assigned MCP Combo buttons to each of these commands using the Linda FSX command list Saved the changes Reloaded linda just in case Valves still Refuse to open. Can someone help me through this? I have spent hours trying to get the Duke and …

Hallo LINDA-Freunde, habe gerade mal einen Versuch unternommen die FLAP-Stellungen für den AirbusX zu programmieren. Das Vorbild ist der Eintrag ND_RANGE 10/20/40/80/160/320 in der Version 2.3 Möchte einfach die Flaps über einen Stufenschalter betätigen, wie z.B. ND_RANGE. Im Anhang ein Screenshot meines "Editorversuches". Beim Speichern motzt allerdings die LINDA "Syntax-Error"? Gibt es Spezialisten unter Euch? Es grüsst der airbusheinz

Verzeih mir Guenseli aber Ich bin desperate and used some of my terrible German grammar hoping to attract you. Please, if you have the time see my post about the Linde Tracer. Every time I have folloed the process the same result but the valves stay closed. I have tried the same MCP keys on other commands for the Duke and they work. ..so the MCP is not broken. Btw...My best wishes for you long family vacation. Regards NealH

Hi guys, I dont suppose anyone would be so kind as to share a LINDA config for the CS707 if they have one? Im having trouble setting it up. Take the heading, for example - I can see LVars in the LINDA Console LUA.0: [L] LVar: L08_011_KNOB = 82 LUA.0: [L] LVar: L08_005_BUG = 1.21 but im have a real hard time assigning this to my VRInsight MCP Boeing panel. Also, i have found L09_002_LT = 2 and L09_002_LT = 0 for the press and release of the G/S button. Can someone just tell me what the LUA functions would be? This is what i have so far in my new CS_707 module i created: function CS_707_GSlope_Press() ipc.writeLvar("L:L09_002_LT", 2) end And …

Hi LINDA Friends, I am a LINDA Beginner, please excuse my bad english!! 've programmed my overhead for the Aerosoft Airbus X with ARCAZE Boards and LINDA. LINDA is a great program all the switches and buttons work perfectly!!! But now I have a problem: In the EFIS panel I connected the rotary switch for ND RANGE, see picture2, LINDA see picture1. I can turn the switch from left to right depending on what I choose in LINDA incr or decr. But I can not turn the switch back ? What do I need to turn the switch in both directions? Thanks for help! Greetings airbusheinz

Hallo LINDA Freunde, mal zur Abwechslung eine banale Frage: über ARCAZE-Platinen habe ich diverse Schalter, Taster und Drehgeber zugeordnet, es funktioniert auch zufriedenstellend. Im LINDA-Menü des Airbus Extended habe ich meist 3 Funktionen zur Wahl z.B. ND RANGE incr, ND RANGE decr, ND RANGE Show Was bedeutet bitte z.B. dieses ND RANGE Show ? Es grüsst der airbusheinz