LINDA Support

Hi, is there any LVar or any LUA-script whivh I can read The set transpoder squwack with? Cheers

Hi, I have installed the 2.6.4 version in P3D v3. Everything seems ok (fsx sync and so one...) but buttons are detected in linda but do nothing in p3D (even the linda "gauge" that I used tho have but I have a message when I restart Linda) and in the console I have a lot of : FSX2D_EnumAndRestore RangeCheck 00000000 Thanks in advance

Hi all, every time I close LINDA (2.6.3), Windows (7/64bit) is prompting "Access Violation at address 007C0BBA in module "Linda.exe". Read of address 000000000." The program itself is working, though. It's just annoying when closing down. Any help greatly appreciated! Thanks, Michael

Hello, a question regarding removing joysticks/hid devices from LINDA. I am at the 10 device limit, but I don't need them all in there. How do I remove the ones I don't need to make room for the ones I do need? Many thanks, Dust

On my built TQ i use toggle switch for engine1 idle and engine1 cutoff, as well as engine 2. I program Linda ngx ENG1 cutoff when pressed and ngx eng1 idle on release. But I do have a disturbing action when switch is pressed. After a few seconds, the handle returns to idle when I want to stop the engine(s) The engines does not stop of course. What kind of signal is supposed to be given to the sim, to keep the handle down, switch closed/pressed?

Hi to all, not been on here for a while but back with questions once again. This is more of a LUA question but this seem the best place to post my query. I haven't yet got seriously into LINDA but I am playing around with some LUA Plugins handled by FSUIPC to get myself started with things. I've run into problems with toggle switches. I have at the moment 11 physical switches which are SPST - so either on or off. I'm struggling to keep these synchronized in FSX. They operate a start panel on Aerosoft's F3 Lightning. The following code works to move the switches up and down in the sim: while 1 do -- -- Prgramming Starter Panel Switches -- --Pitot Heater i…

Hi guy, I need your help on this (thanks in advance). As I am using a joystick now and would like to set the key for the Radio Control Panel Switch. I have been gone through the LINDA Aerosoft Airbus module but I couldn't find that. Can you please advise where is it? Thanks

I am having an issue with the action "On Button Release".setup: Saitek yoke, throttle, switch panel (no Saitek drivers), SPAD (for switch panel, all buttons unassigned in Linda, Global Shift not selected), FSUICP4, Linda 2.6.4. In my action.lua file which is very large I have 2 actions set on Button 0 on the yoke. one for On-Press and one for On-Release. The functions are below. I use button 0 as a 2nd shift command in each Linda shifted Panel. In each function in my action.lua file i evaluate BShift and based on it being a 0, i perform an action. I perform a second action if it is a 1. The problem I am having is that sometimes after button press, BShift = 1 and remai…

Can someone help me understand how I can extract this table in Linda's lua action.lua file. I want to display the 6 nearest airports in a Lua display. 0658 [120 bytes] This area provides a table of data about the 6 nearest airports to the user aircraft, in order nearest to furthest. This works properly in FSX with Acceleration, and should work okay in SP2 versions. It should also work in P3D. 1.4. Each entry is 20 bytes long, consisting of 4 fields as follows: 0 4 bytes ICAO ID of the aircraft. If this is 3 characters only the 4th will be zero. 4 4 bytes Latitude of the airport, in degrees, as a 32-bit Float (N positive, S negative). 8 4 bytes Longitude of the airpor…

Hi guy, Since I have 4 spare turn buttons on my panel, I would like to set those up for Aerosoft Airbus ND / PFD / ECAM 1 / ECAM 2 brightness switches. How can I possibly do that? May be this is related to “axis” setting? Many thanks for your advices in advance.

Hello Guy's i need help I can't use my saitek panals for the Aerosoft Airbus.... -> Multipanel -> Radiopanel -> Switchpanel Can one send your configuration of the Aerosoft Airbus in Linda ?? PLEASE FSUIPC is installed. Switchpanel: Radiopanel: Multipanel: Thanks You can find me on: Steam: http://steamcommunity.com/profiles/76561198201477938/ Twitch: http://www.twitch.tv/haui1994 Skype: the_haui Please help me best community

With the new P3Dv3, I'm using some aircraft directly in P3Dv3, some are installed in P3Dv2 and used in P3Dv3 and some are installed and used in P3Dv2. Now I'm wondering where to install LINDA to have connection to all 3 different setups. How am I going to setup LINDA, so I can use all my aircraft?

Morning Just noticed these in the LInda window. any ideas? D:\Program Files (x86)\Steam\steamapps\common\FSX\SimObjects\Airplanes\mjc8q400\MJC8Q4.air Exception 3 "UNRECOGNIZED_ID", Ref 2750, Index param 1 on write SetData for "RECIP ENG FUEL FLOW:1" Exception 3 "UNRECOGNIZED_ID", Ref 2751, Index param 1 on write SetData for "RECIP ENG FUEL FLOW:2" Exception 3 "UNRECOGNIZED_ID", Ref 2752, Index param 1 on write SetData for "RECIP ENG FUEL FLOW:3" Thanks

hi just started writing modules . would like some help scripting a rotory switch controlled by a Lvar variable with 4 positions. in the tracer when the switch is rotated up it reads ERP_ATR=1 ERP_ATR=2 ERP_ATR=3 when rotated down ERP_ATR=2 …

First of all to ScotFlieger - a huge thanks for all the incredible work you've done! Equal thanks to the founders of Linda for such a superb piece of software. Having played around with Linda over the last week or so it seems to suit my needs perfectly. One big question that I am hoping Scot might have the answer to: which MCP to purchase from VRInsight? I fly the following aircraft: FSLabs Concorde X, PMDG 737 and PMDG 777, Aerosoft A318,320,321, A2A C172 Both MCPs seem to work well using Linda but I can see myself flying the Airbus more often now that the 737 is being phased out of the BA fleet. (Yes I fly for BAV) (Of course I, like many, am eagerly…

LINDA version: 2.6.3 LINDA module name: PMDG 737 NGX version 1.9 Sim version: FSX Aircraft: PMDG 737 NGX, latest version I found out about LINDA yesterday, and today I wanted to try it out. It's been quite easy to get everything working, but there's one thing I just can't work out. I've got the unshifted and shifted 1 working. With that I mean that when in mode 1 on the yoke (which is unshifted) I can assign buttons, and they do what I tell them to do in the unshifted window. When I change to shifted 1 (mode 2 on the yoke), the buttons do what I've told them to do in that window (so shifted 1). But when going to shifted 2 (which is mode 3 on the yoke), nothing happ…

Hi i installed win 10 and when i run linda and i choose " make change for you" i get the meaage "too many devices in your config..." i don't understand the meanning and what i have to do. thanks Menachem

How are you guys getting Course control using the VRInsight MCPII ? This is one feature that I want to use but there are limited rotating knobs so I just wonder if anyone has a smart way to get this to work easily? Thanks.

I am working on the linda with a latest version of fsiupc and linda 2.6.4 with a trying to map Airbus 320, but when even i want to start linda it came out with a Red Line ***Lua error: ...eed Martin\Prepar3D v2\Modules\linda/system/init.lua:41:module 'linda/libs/._lib-aivlasoft' not found: I did go back to the folder and I found that mentioned lib-aivlasoft folder, what's goes wrong? Anyone can assist? Million Thx

Greetings, I am using the following: -MCP Combo II Boeing -Windows 10 64 bit -P3D 2.5.12946.0 -FSUIPC 4.944a -LINDA 2.6.8.147 -USB Serial Port Driver 2.12.6.0 (Future Technology Devices International Limited) LINDA loads and functions correctly. However, when I unload an aircraft and/or close the simulator; the information screens on the MCP Combo II retain the information, current as of the time the flight was unloaded. This has never occurred before. Any idea what might be causing this, and what can be done to correct the situation? Many thanks, in advance.

I am running FSX SE, Saitek X-55 controls, Saitek pedals, and LINDA 2.5.7. The latest paid-for FSUIPC. Well, I got 2.5.7 installed and set up the A2A C-172 perfectly. Got every button and switch to work just like I wanted. Took 'er up for a few flights, and was very impressed. So my next task was setting up my Carenado Grand Caravan EX. Since there was no module for it, I simply loaded it up, and started TRYING to make things work. I started out with the default FSX lay-out, and it already had the Parking Brake set for my joystick pinkie switch. Worked great. Next was the flaps - Incr up and down to two switches on my throttle. No work. I tried setting the elevator t…

Hi, When I try and create a new folder for a new aircraft and save it I keep getting the error I/O 183... Dave

i have 2 bux cards i connected the first and defined 32 toggles and every things ok i connected the other card and linda recognizes the toggels of the firs as belong to the second. shuld i define all the toggles again ?

Hello I recently bought the VR INSIGHT MCP BOEING TYPE COMBO PANEL. Unfortunately, I have some issue with the displays and PMDG 737 NGX. The software loads with fsx and everything works great apart from the MCP displays for SPD, HDG, ALT and V/S. The values on the MCP unit stays frozen without a change when I rotate the knobs. The values in the NGX mcp are working well, they do change when I rotate the knobs but VRINSIGHT MCP is all at 000. Nothings helps until now. I read the posts on the forums but there's no any solution apart. My config is as follows: - Newest LINDA software 2.6.3.148 INSTALLED - PMDG NGX newest modules installed in modules->lindacfg-&g…

Howdy, Gents. Been on an extended hiatus from simming, but was getting back into it. I've been getting back to it, but have been having weird errors with Linda. The error I get is: config-hid:LUA:3 attempt to index field 068E00510 (a nil Value). This started when I tried to update the Majestic Q400 module. I then updated Linda to 2.6.3, and then reprogrammed the Default aircraft. The default aircraft worked fine. I then tried both the Majestic q400 and the MD11 and got the same error. Not sure what to do here. I use a Saitek Yoke, an old rudder pedal that gets recognized as a joystick, a v1 VRI MCP and a VRI "push button" panel. (This last thing reads a…