LINDA Support

Hi everyone. Leo Bodnar sells a HID Interface for 128 inputs. How many inputs can be used max with WIN10 and LINDA? http://www.leobodnar.com/shop/index.php?main_page=product_info&cPath=94&products_id=180

Hello, is there any possibility to ahve LINDA (3.2.6) started up when P3d V5 is started ? Thanks in advance Claudio Damiani

I need help for my saitek radio panel in FS2020 - A320N aircraft. It does not communicate with the sim

All of my flight sim peripherals are Saitek. I'm running FSX:SE, FSUIPC version 4.975A, and LINDA 3.1.1 for FSX/P3D 32-bit. I have connected a X-52 H.O.T.A.S. (stick and throttle), a Pro Flight Yoke (yoke and one throttle quadrant), two additional throttle quadrants (call them Quad 2 and Quad 3), a Pro Flight rudder, a switch panel, and a radio panel. I have previously used--and programmed--all of these, without a problem. I've cleaned up the cabling arrangements, and did some other housekeeping, and I've encountered a problem with LINDA that I've run across before and wound up requiring a total reprogramming of the buttons...something I'm trying to avoid this …

I am using the current LINDA with FSLabs and P3dv4.5. First, I have an issue with the landing gear. After configuration, the visual gear lever does not react and the gear only extend. How do I solve this issue? What "gear" choice do I use? Secondly, I cannot locate the correct choice for the flaps. Can someone direct me to the correct choice for the flaps? Thank you Michael

HI I purchased three products at VRinsight in 2013: CDU II, MCP Combo II - Airbus FCU and MCP Combo II - Boeing MCP Always use VRinsight software (http://www.vrinsight.com/devel_shot/index.html ) But it hasn't been updated since July 11, 2016. Contact them, arrogantly, our software will not be updated. I am very happy to see that your linda area can be used with VRinsight today. There are a few questions I would like to ask: 1. In addition to VRinsight driver files (VRiSim), can other LINDA be used? 2. Can MCP Combo II - Boeing MCP and CDU II be compatible with PMDG744v3 and QW787? 3. Can the MCP Combo II - Airbus FCU and CDU I…

Can't add this to the Majestic Dash 8 Q-400 (module 2.6) thread, but if anyone is interested in the inputs for the Q400 FMS in LINDA, here they are. Paste this into your User section of the MJC8Q400 profile and you should be good to go. -- ## FMS ############### function FMS_LSK_1L () MJCD8_Write(1, 79415) end function FMS_LSK_2L () MJCD8_Write(2, 79415) end function FMS_LSK_3L () MJCD8_Write(3, 79415) end function FMS_LSK_4L () MJCD8_Write(4, 79415) end function FMS_LSK_5L () MJCD8_Write(5, 79415) end function FMS_LSK_1R () MJCD8_Write(6, 79415) end function FMS_LSK_2R () MJCD8_Write(7, 79415) end function FMS_LSK_3R () MJCD8_W…

I am quite a Newbie to P3V5 and all the add-ons, so please be gentle 😉 I managed to get everything up&running with the latest versions of all that add-ons and "modules" with only some glitches left. But: In wondered why there is no working VOR/ILS within Prepar3D. First I thought the data within the scenery is outdated and "injected" actual data via Navdatapro. Even with the right values, for example EDDL 23L ILS IDSW 109.9 no Info from the ILS, no glidescope etc etc. By chance the VRinsight FCU (Airbus) was disconnected and, big surprise, the data was there, reconnected, data gone again. Perhaps there is an issue with the A320 module, Linda and F…

Hello all, I have just received my week one order for the new Honeycomb throttle. Anyone have any ideas how the autopilot system can function (specifically the number dial). If anyone needs details on what it's like, let me know. Thanks in advance!

Hi everyone. After many hours trying to config the MCP1, with LINDA and the Dash8 of Majestic, I can't to make it work, i've got the dash8q400 module, but it's doesn't work. Any help please.?

Hi all, I remember supplying the Alpha yoke ID when it first came out, and having received the HC Bravo Throttle Quad today, I thought the new ID may be useful as well. The 'Bravo' is currently listed as 'Other' under the Linda "Setup Joysticks" tableau . 294B19010 ● Bravo Throttle Quadrant → Axes: 6 Buttons: 48 Hats: 0 [A6F52D0920273B0]

Hello, I have a Problem with the FCU Combo and FsLabs Airbus. The LCD Displays always works as an Info Panel and didnt Show the Actual in Sim FCU settings. I tried to select the commands for Display Switch (Original Aircrafts) and that didnt work. I couldnt find any commands there in the FsLabs Profile. Anyone got an Idea to solve this? Thanks Daniel

Hi friends, The problem of the day, after a reinstallation of P3V4.5 I reinstalled FSUIPC6 as well as LINDA 3.1.1. In the Summary all the paragraphs are OK except the last Flt Sim / FSUIPC, configs which tells me that action is required. I have the following lines: P3D-64 and FSUIPC 6.000 runing FSUIPC files not found! I used the VRISim program to find the correct COM port which is 3 at home. LINDA and FSUIPC6 are present in the P3D Modules folder Do you have a solution to this problem ? cordially Jean-Luc

Hello! I use the Maddog with LINDA and where unable to find the binding for the "Takeoff/Go around" buttons on the throttle... Did I oversee something? Thank you very much!

Greetings, I recently bought the FCU Airbus Version from Aerosoft/Vrinsight. I installed evrything right after the book, usb-driver, Linda and fsuipc (reistered) Of course I got the message that we have to live with a lot of limitations. Thats quite frustrating because I bought this hardware to have the special Airbus "look&feel". I am using a Goflight MCPro panel, but thats designed for "Team Boeing" and lacking all the set/managed options. At the moment I was only able to get some very basic things to work like changig values for Speed, HDG and Alt. "Deeper" Functions like switching QNG/Standard, Rose and Range as well as all other "buttons" do not w…

Hi I am trying to connect my Stream deck to the FS2020. I have installed Vjoy and UCR and up to there everything is active. i have installed LINDA. it gives me all green.... On FS 2020, I can see the VJOY in control and I see a text saying LINDA IS UPDATING COMMANDS. BUT.... it doesnt work... any advices? hints? something?? thanks alot!

When I click the LINDA 3.1.1 download link and all the other download links a window opens briefly and then closes. Thanks in advance

Hi there, I have a quick question and hope you can help me. Today I installed FSUIPC 7 (registered) and LINDA 4.0.3 to my MSFS 2020. I own the VRI MCP1 and connected it to my computer. After setting up the MCP1 in LINDA and restarting FCUIPC 7 some knobs on the MCP Combo work and some do not. In MSFS I loaded the FBW Mod A320 Neo Airbus. V/S, ALT, HDG, SPD, BARO knobs and also light switches on MCP are working fine but I can't manage to make the EFIS part working. With the CTR and TFC knobs I wanted to adjust the map mode and the map range of the NAV display. On the EFIS mapping page of LINDA (Ident GPS, Mode 1), I tried different things like EFIS MAPMODE inc/dec or …

Hi Guys, I own the MCP1 and just installed FSUIPC7 so that it will work with MSFS2020, followed the instructions, everything seems fine in the LINDA window but no response at all from the MCP1 or the MSFS when i try to tweak the autopilot ion the sim.. PIC any ideas?

Hello, Since the update to MSFS 1.10 end of octobre or begin of november (I don't remeber exactely the date), the Saitek Switch Panel doesn't works anymore ! I didn't change anything in my settings, just did the MSFS updtae. The saitek radio works always perfect, just the switch panel. An idea of the problem ? Thank you.

Hello, I just received my honeycomb yoke and I am trying to assign the lights on the yoke to the corresponding lights in the plane, but I haven't had any luck and I am pretty lost. I have assigned the function in the joystick assignment page, but when I move the switches on the yoke nothing happens. This is my first time using a program like LINDA. I am on P3D V4.5.13.32097 and NGXu version 2.91.0746 Here is a screenshot of my joystick assignments page: https://www.dropbox.com/s/d2wvt9ecp2j43yz/honeycomb.JPG?dl=0 Thank you, Robert Briscoe

Hello, I've been using LINDA 3.2.6 with the QW787 v1.1 module for the MCP Combo II for a month now. For the most part, it works very well. Thank you for the great job. But there is a small problem with a key assignment in the EFIS sector. I have assigned weather, traffic and terrain to three buttons. These only work when I first activate the three buttons with the mouse in the virtual cockpit. Did any of you have the same or a similar event? Is there a solution for this? I am using P3D V5 / V5.1. With regards from Austria Thomas

I purchased FSUIPC7 and installed LINDA 4.0.3, but when I opened linda, the warning "some key LINDA/FSUIPC7 files are missing.check LINDA2 LOG for details" appeared. Cannot connect with Vri MCP II combo

Hello, Fsuipc has switched to a paid version and is launched at the same time as FS2020. So when I then run Linda .... MCPCOMBO not active. I must first run FS2020 on my own (without the shortcut to Fsuipc) then Linda then then Fsuipc. Approach which was the one you recommended with the beta version of Fsuipc. Do we have to do another maneuver with the shortcut FS2020 + Fsuipc launch at the same time? Thanks to a reponse FCY ISA Christian

My VRi MCP no longer works, could this be A. Because I now need the paid version of FSUIPC B. Because I've installed the FlybyWire A320 C. Something else,? I've installed MSFS updates as they came along and the flybywire 320 Regards Terry