LINDA Support

Does Linda support THRUSTMASTER throttle valve?

Dear Andrew The total functionality of the MCPCombo compared to P3Dv5 in MSFS2020 is not the fully 100%. The EFIS-part is not available completely(yet). Is there any perspective when you will have fixed this working? Hope to hear Regards Theo

Hello everybody, I've been using LINDA since September 2020 and it works quite well with P3D V5.1. But since the update to V5.2 I get the warning message "Unable to assign Ctrl+Alt+Shift+F12" more recently. No function is assigned to this combination in the P3D. Otherwise the program works normally. Can somebody help me? Best regards Thomas

Hi everybody, for my first experiment with LINDA i'm using a BODNAR board BU0386X with the FSLabs module correctly installed PIN 5 e 7 are reserved for ENG MODE SELECTOR with this configuration: PIN 5 on press: VC PED ENG MODE Start / on release VC PED ENG MODE Normal PIN 7 on press: VC PED ENG MODE Crank / on release VC PED ENG MODE Normal When i move the switch in "start" simultaneously the flap levers move from pos 0 to pos 1 and if i repeat the action the lever goes to 2 then 3 but not on FULL.......it's strange. My first thing is that the Bodnar is not working well...but someone of you have an idea??? Thanks in advance …

Hi all, Linda 4.0.5.173+FSUIPC7.1.0 clean install During startup of MSFS COM panel can be tuned, selected and swapped for all functions; COM-NAV-ADF-DME-TRN Just before the Welcome page of MSFS kick in, the COM functions get locked, cannot be tuned or swapped. Any clou?

The FSL A320 Sharklets release has some different mouse rectangle values when making Mouse Macros. This makes it difficult to assign functions as common to both versions. I cannot find how to differentiate them ... ie the Title or Name identifier is the same for both of the planes. Can anyone help ? thanks PS. This is for P3Dv5.1

I have looked and looked but I cannot find the Function for turning the LEDs on and off (LAMP button). I would like to turn on the LEDs and leave them on. Currently the lamp button doesn't toggle, the LEDs light only when the button is held in.

Hi All, I'm making a home cockpit for the Majestic Q400 and I've just finished my Weather Radar panel. I've downloaded the excellent LINDA files for the Q400 however no controls for the Weather radar are in the file for assignment to my panel. I've worked out how to do the Weather Mode (OFF, STBY, TEST, ON) as well as the Wx, WxA and GND MAP modes. I'm stuck on getting the programming right for tilt and gain functions. Additionally, I'd like to make a toggle function for the Stab control. Here's what Majestic supplies about these functions: Name Index Type Dir Cockpit UDP Description WXR_->controls.stab_off_cntr F602 BYTE IN…

Hi Artem, hi Andrew, I just noticed on setting up LINDA 4.0.5.173 with an ARCAZE USB HID that there seems to be an issue having multiple virtual HID devices based on the same Hardware ID. Still shows the same assignment page and thus doesn't allow to assign multiple functions as then the Button-IDs between the different devices are shared. In Arcaze you are able to create multiple virtual HIDs (here "Lights" and "AirCondEng" named) and assign the 40 digital and 6 analogue inputs to Joystick buttons. As Arcaze has more Inputs than a normal Windows HID, you can split that to multiple "virtual" HIDs. In Windows (10) it's shown correctly then and you can t…

I am using p3d 4.5 in windows10 FSUIPC 5.157,linda 3114. I start the sim and "every is ok" in linda. Nothing happens in the mcp when I turn knobs or push buttons. I go to the setup MCP Combo page and enabled checked, fsuipc.ini [VRInsight] 1=com4 I need some help Thanks Paul

Is there any hope that LINDA will allow the VRinsight to control the MCP of this aircraft? I read elsewhere on Avsim that people can get the Honeycomb Throttle quad to change altitude, etc. Does this also work with LINDA and VRi?

Hi, Thanks for all the support! I have a question regarding the 787 Linda. With last update of Qw787 (v1.4) it seems that some buttons are becoming active with Linda only after being pressed on the aircraft itself... Anyone else encountered this issue ? For example before starting a flight I’m clicking TFC WXR TERR ENG etc buttons to make them active on the panels with Linda. Strange !? Appreciate any idea Thanks

Is there any chance to upload the file again ? Link is dead in this post: captainsim757iiip3dv4-linda-module Thank you

Hi, I wanted to ask will there be an update regarding the usage of lvars and hvars in Linda as Fsuipc have enabled LVAR and HVAR through WASM module. Regards

Heya! I would like to write a small script to use a button press to increment or decrement the prop axis by a certain amount (the default built in prop incr/decr are not the correct amount for the plane I am flying resulting in multiple presses needed to get the position I want). So my questions are: how do i "read" the current prop axis position in the sim and put it into a local variable.... if it was an LVAR i would write something like local prop_position = ipc.readLvar("L:insertLvarnamehere") 1. How do I do the same thing for the fsx value? 2. What is the range of values? 3. I know how to write it back to the sim - would use ipc.control(…

Hello. I'm completely new to LINDA and FSUIPC. I'm trying to assign controls for the default Asobo Cessna 208 B Grand Caravan. Specifically, I'm trying to identify and assign to a control button on one of my controller inputs (I can't really call them joysticks). In this particular case it will be on my Virpil VPC MS-T 50 CM Throttle. The 208 B has a 3 position toggle switch controlling the fuel boost that is manipulated during startup. The 3 positions are On/Norm/Off. In MSFS 2020 you can use the Fuel Pump control settings to set the fuel boost to the "On" and "Off" positions. However, you need to be able to set it to "Norm" after startup for normal opera…

Hello, after reinstalling Prepar3Dv.5 I have problems to run my MCP-II/Boeing Type v1.100 with Linda. Joysticks/HID devices is everything ok, VRinsight MCP Combo is everything ok and Flt Sim/FSUIPC configs is everything ok. After starting the FS with PMDG 777 the MCP panel does not start. I have had this problem before recently. Can you help me again please ? Greetings Claus

Hi Andrew I have downloaded Linda v 4.05 eand is ok and active in MSFS2020. As so far everything ok. :) But ....when my MCP/COMBO-II is resetting/starting up, I see in the com-display (right-side) that the device is Powered by Linda v 4.04 Can you help me to assist to get this synched? regards thx Theo

Good afternoon, my system: Prepar3Dv4.5,Win 10 64 bit. I have installed the PMDG 777-300 and now I want to program my Vrinsight MCP II Boeing Panel with Linda so that I can control knobs and buttons on the 777-300. When I call Linda (Summery) the positions Joysticks, Vrinsight MCP combo and FSUIPC are all highlighted in green. At the top of this page you can see "PMDG 777" framed in orange. On the second page (Setup MCP Combo) also everything is green and marked ok. I start the simulator to program the buttons and knobs (with the tab MCP Combo). Unfortunately this does not work. Can you please help me? thank you very much in advance. Claus Translated with …

Hello, I have tryid to follow all the steps, LINDA not connect to MSFS: 1.- Run MSFS 2.- Run LINDA 3.- When airplane is on stand ready for flight, run FSUIPC7 (Registered) But on LINDA 4.04 is in red colour the message "Flt Sim or FSUIPC not running" and "SYNC TO SIM" is not on orange. Anybody help me? Thanks and best regards

I'm finding that the control for the engine 2 thrust reverser is actually operating engine 1, in the same way that the engine 1 thrust reverser does.

I have GF-EFIS device, does LINDA support the configuration of this device in the application? When loading LINDA I seem to see every USB Device in the HID controllers except the EFIS 09F300400 ● GoFlight GF-LGT control module → Axes: 1 Buttons: 3 Hats: 0 044F04070 ● TCA Q-Eng 1&2 → Axes: 8 Buttons: 31 Hats: 044F04050 ● T.A320 Pilot → Axes: 6 Buttons: 17 Hats: 1 09F300300 ● GoFlight GF-T8 control module → Axes: 0 Buttons: 8 Hats: 0 06A30D050 ● Pro Flight Radio Panel → Axes: 0 Buttons: 24 Hats: 0 09F300200 ● GoFlight GF-P8 control module → Axes: 0 Buttons: 8 Hats: 0 09F300301 ● GoFlight GF-T8 control module → Axes: 0 Button…

Does LINDA 4.05 support MSFS2020 Aerosoft CRJ 550 700? I installed, and find the temple of CRJ 550 or CRJ 700, but no key actions can be chosen. Thx for help.

I always loved LINDA! It made it possible to use my Saitek Switch panel and MCP Combo, as well as made it easy to configure joystick assignments for different aircraft. But this was in the FSX days, when I basically only used add-on aircraft. Now that I'm using MSFS I noticed that it doesn't seem to be possible to create different sets of assignments for different MSFS default aircraft. Is that right? I mean, for instance, the assignments for the MSFS B787 must be the same as for the MSFS X Cub? I tried to create a new module, but I can only select from the list of add-on aircraft in the Community folder. If that's the case, the profiles in MSFS are actually more fl…

Using P3Dv4 with MJCq400 pro Vri MCP2 downloaded and using module 2.6 All other features working except radios. Can anyone advise? I know the FMS module on Q400 isnt the same as most radio setups - but I'm hoping theres a solution as i know on a previous install I've had the comm radios working