Terminal Procedures Forum

Hi!I'm interested in working and correct SIDs and STARs for PMDG 744X (FSX), is it possible to create them automagically from some data? Manual creation ofсourse is not an option :(

Hi TerryThanks for your good work on the iFLY 747. I just loaded the terminal procedures and find that the SID speed entrys are missing off the FMC flightplan legs page. I checked the original SID example and that that loads all the speeds OK. Not sure what's missing but you can't use VNAV with speed hold till reaching cruise level where the speed fields are entered.

Hi Terry, posted at pmdg by error - tsk. - Think the link to here needs a revision.There is a serious error with the EGLL.txt - SAM sid around Ockham vor - OCK3 has 5W as longitude so ends up around the other side of the UK - more like an OCK200 lolWe all make mistakes, as the dalek said climbing off the dustbin ;o)John E

If so what happened to it?

Hi Terry,I purchase MD-11 few weeks ago my question is sidsstars file on EHAM there is nothing between RNWS and ENDRNWS. i can't see NONE under both SIDS and RNWS on FMCDilip

HelloTaking SBRJ as an example, is it correct to say that an FMC, as capable as it is on say a 737-7/800 etc. series (take the PMDG version as an fs example), can take you to the end of a STAR and that such approaches to touch down are then down to basic raw data flying using NDB/DME etc. combined with V/S or FPA functions ?or, can an FMCs be programmed with such DME/NDB approaches, if yes do any FS add-on support this type of approach?Thanks, anyone, for your help to clarify/understandjlm

Hi all,I was wondering if I could solve this problem. I have installed many new sceneries from Aerosoft and FLYTAMPA, and the problem is following the ATC directions when taxiing.When I taxi sometimes with any aircraft, I will obtain incorrect instructions for taxiing, especially with the new products and I don't know why. I understand how to taxi well using the Alpha Beta Cuba language and how to interpret the taxiways, however it seems that this is wrong in FS.There are times when I taxi, and after writing down the taxii instructions, I try following them, but they take me to wrong taxiways but to the right runways. At the end I get there because I decide to take any ta…

Hi Terry,Is it possible to place multiple RNW entries in an approach in the same way as one does in a SID? Failing that, is it possible to have an approach WITHOUT a RNW defined at all?I'm trying to write a procedure for the KPDX VOR-A approach, but I'm sure the technique would be the same for all lettered approaches. At PDX I can use RNW 21 since the approach would come in to that threshold, but at other airports there may not be a runway threshold in line - often it's the VOR colocated at the field.The other problem I'm trying to code is an approach where the Missed Approach Point is well before the airport - there's one at KSFO and there are others. Basically the wa…

Hello!I have an old (0608 cycle) PMDG TP set which contains approaches for my home airport VABB. Now, these days I am flying the iFly 747 for which the download from www.planepath.com do not contain any approach data for VABB.Is there any way I can easily convert from PMDG sidstar -> iFLY sid/star/app files? I know the documentation is out there, but in case there is an utility to help, I would really appreciate it.Thanks,Arvind.

Terry,I have to add two approaches to KIGM.Before starting I checked the current .xml in the Level-D.I cycled the current approach (PAR03) in the Level-D FMSand the runway waypoint (RW03)is some distance fromthe airport symbol on the EHSI display.The procedure is cycle 0810.I think this may be an older KIGM.xml LAT/LON for RW03.Also the approach name is PAR03.But The FAA plate I downloaded is named GPS03??I do not know, maybe the name and lat/lon is not current?****<?xml version="1.0" encoding="ISO-8859-1"?>** Runway 03 sectionRW03Runway35.194225-114.017861034490at

KLAX.xml Cycle 0810I found e.g.:ILS06LMissing main appr waypoint NATHN and the hold is at POM and should be AMTRA.KOYEV could possibly be used instead of radial intercept.ILS24's are missing many approach transitions/waypoints.Looks like the FAA made many changes this time?I think the entire xml needs a review.

Hi everyoneI am new to forum and to ask for help with a problem I'm having.Have purchased and installed 'The Queen' but have not been able to activate at any stage VNAV.VNAV does not arm or actvate following loading FMC or will it arm or activate during flight. LNAV is not a problem.When I try to arm VNAV is lists a message 'unable cruz alt'. What am I doing wrong?Thanks for your helpPeter Murfitt

I have the FSX versions of the PMDG 747-400 and the Level-D 767-300ER installed but appear to be having a couple of issues with the VHHX (Kai Tak) terminal procedures for both aircraft as follows:-1) Level-D 767-300ERThe SIDS and Approaches for runways 13 & 31 appear in the DEP/ARR page of the FMC but no STARS appear. When I open the XML procedure file for VHHX there doesn

KSAN.xml cycle 0809 for Level-DdepartureBRDR5rwy27 transition**************** below has no name: Also, waypoints 1 and 2 have the same Lat/Lon.Should intercept a PGY radial before going to BROWS?Normal32.610333-116.979083000at(INTC)Intc32.610333-116.979083000at01200Leftrwy 09 transition*****************The first intc goes out 172nm!May have to check them against the actual procedure.

Hi Terry,First off, thanks for all you do, keeping up with the TPs and all. Thanks especially for keeping it free. I'm writing to ask if you would give me permission to upload the TPs for the LVLD 767, ATR72, and PMDG, cycle 0613 from 2006, to the AVSIM Library? This cycle matches up with the last free AIRAC released, also available in the AVSIM library. There are many folks, I believe, that don't update their navdata. As I'm sure you're aware, having different dates on the AIRAC and TPs can cause issues. If these are already available and I missed them, I apologize for taking your time.Best Regards,Jeff

Hello Terry,Is there a difference in using the keywords NAVAID or FIX when building PMDG procedures? ThanksJAR

Is there any way to obtain Terminal Procedures version 0802? I'd like it to match up with my slightly older AIRAC Navdata version at least for the moment.Kim

hi Terry,first of all thank you for providing us with your great work!i just installed your terminal procedures for the level-d 767 in fs9. the SID's for KPHX seem to have a problem, though.please take a look at the screen shot of the fmc that shows the legs for the TFD2 SID off runway 25L.any thoughts on this?thanks!Denisedit: in case it isn't obvious, the second leg looks kind of weird ;)http://forums.avsim.net/user_files/190516.jpg

Hi,Just noticed the above are missing from the 0807 updatethanksGraham

Terry,Any suggestions on where I can find subject airport's SIDS/STARS/IAPs for LevelD?I found same for PMDG products at NAVdata, but can't find anything for LevelD.Thank you.Paul Kuhn

Hi.I am looking for terminal procedures (SIDSTARS) for the following airports in East Africa - HTDA, HKJK and HUEN. Can anyone help me in this?CheersPopo

Terry,I have the PMDG 747 Queen and I just discovered why my sids/stars aren't up to date with my airac file I get from Navdata. I have not updated my sid/stars with your file. What are the "NO HOLDS" files and how do I use them?Thanks,Lynn Fisher

Hello,After a FS9 reinstall, I reinstalled the LevelD 767 and then AIRAC 0801. Followed by that I got your 0801 Terminal Procedures..Whenever I go in my FMC, no airport has SIDs and STARs. All the files are in the correct spot, but the FMC is not picking them up. I have recently just tried AIRAC 0802 and your new set...No luck..I also tried a package from navadata.at and still no luck...Do you have any ideas or suggestions?ThanksJohnny Ginley, WWA1559LevelD 767 Captainwww.flywestwind.com

Terry,First of all a big thanks for all that you do to enrich our simming experience with your work. I have been a happy user of your data for as long as you've made it available. Having said that, I was wondering if you could take a look at the data for EGLL. Myself and two of my friends flew from EGLL to VHHH in the new PMDG 744F and when we started up at EGLL, it gave a runway error code 5 after loading the flight plan. We all had 27L programmed as part of the flight plan through FSBuild. Anyway, after loading, we got the error but continued on as the ND showed the runway anyway. We also noticed that there were no SIDs available to us from the ARR/DEP page of the…

This is the first "fix" given in the most used (flightaware.com) flight plans between KMCO (Orlando FL) and KHOU (Hobby): FMYDT PIE REMIS Q100 LEV MHF1. I can't figure out what it is, it is not a fix according the airnav database and it's not a DP for KMCO (I've got all those). The flight paths depart SW from the airport and then turn W towards the PIE VOR. Anyone know or have a clue?