RXP GTN 750/650 Touch

Hello, I've been dealing with the issue where I cannot get the 3D model of the GTN to work in the Carenado 206 steam, only the 2D model pops up. I have tried reinstalling both the aircraft and the GTN and have had no luck. When I go to turn on the GTN, the popup appears but the default 530 stays in the 3D panel. The GTN works into the 3D panel just fine in all my other aircraft that are compatible for it. Attached is the .ini config file .. [GTN] ; comma separated list of gauges gauges = GTN_750_1 [GTN_750_1] ; comma separated list of render targets. drawto = WINDOW, PANELS, PANEL_3D ; is the master device if true. MasterDevice = true ; aviation …

I have a GTN Reality XP 750. I installed in it seems to be in the Panel of the Carenado PC-12, But the power does not come on when the avionics are powered on. Can anyone help?

I get a message, "License invalid: Contact Vendor" when I start X-Plane and then click the "Touch to continue" on the GTN 750 screen. Everything worked perfectly last night. Any suggestions?

Hello, im new in this plataform, i buy the GTN750 an I was wondering if i can put the gtn750 in the GULFSTREAM GIV of the forum im not very good whit the config txt and those thinks if someone can help me I'll be very greatful thank u guys

G'day, I've encountered a bit of a conflict between the GPS OBS and the stock CDI switch in the Carenado Grand C208 HD I was hoping someone may be able to help with. Out of the box everything looks good until you go to OBS a waypoint - you can't move the CDI in GPS or GPS/OBS mode. You can move the dial until you initialize the GTN unit, then it freezes in GPS mode (although VLOC still works fine and you can still toggle between). It seems that the master/autopilot is really tied to the stock 430 unit somehow. From what I've seen, if you toggle the "GNS NAV 1 CDI" to "NAV" (which is the command for the GPS / NAV switch on the dash of the original carenado c…

Hello, I installed the GTN 750/650 to the STMA PC12. I intended to install the 750 as GPS1 on top of the 650 as GPS2. While with the 750 everything works well, at the spot of the 650 only the bezel of the 750 appears at the cockpit panel with a dark screen. However clicking on this bezel opens the 650 window which works fine too. What I want to achieve is, that the content of the 650 screen is shown within the bezel. Many thanks in advance for help 😏 The ini file: Spoiler [GTN] ; comma separated list of gauges gauges = GTN_650_2, GTN_750_1 [GTN_750_1] CdiScale = 0.949999988 ; comma separated list…

I get a Black screen and if you drop the plug in menu down it says failed version, This is a re install.

Hi. Sorry if this has been asked before but I couldn't find anything answering my particular query. I've got 2 copies of X-Plane on the SAME computer but on 2 separate SSD's. Is it possible to install / run a copy of the GTN 750 on both installations of X-Plane 11. Many thanks ......

"Database Not Found" is the message I get when booting up the Reality XP GTN 750 in X-Plane 11. The Garmin GTN 750 Trainer is installed and working fine. I've tried nearly ever setting in xplane's plugin options and even uninstalled and reinstalled the apps. I'm at a loss! Help Please. Nick

Hello, can i install the GTN 750 on a second computer? I have a touchscreen on my second computer and would like to operate the GTN 750 via the second computer and the touchscreen. Xplane is installed on another computer. Is that possible ? if so how do I have to install that works? Sorry for my bad English. Has been translated with Google Snake82

Hey, because I bought my RXP a few days ago, I still have this black screen on GTN750 panel, just wanted to admit that I don't have Traffic Global.

After I use your parameters, there is no change. Is there a bug in the parameters

Hi, I have a paid version of Reality GTN 750 running on Win 7 - XPlane11, on the Carenado S550. It has been working okay. I purchased this 3 years ago from F1. I needed to re-download this RealityXP to a newly installed version of XPlane 11 running on Windows 10. I bypassed the E-Commerce F1 and downloaded directly from the RX site. The computer has a Dual Boot System. It keeps blocking my Download for rxpGTN due to a virus concern. I opened the Firewall and the Anti-Virus. But blocking still occurs. S550 still works Okay on Windows 10, however. . So I have copied the Plug-in from the Win 7 system, and inserted it In the approp…

I found multiple threads that refer to the "floating" GTN, but nothing I've found so far actually tells me if the GTN can be locked in the panel or if it is always going to float. There is a no-display GTN that appears in the panel and in the manual there is a reference to Freeze Window. But there's no other reference or instructions. So am I correct that the way the GTN650 works is as the floating Garmin Sim panel? For a lot of what I'm probably not going to be moving the panel that much, so I can live with just placing the floating sim over the "placeholder" in the panel. But it sure would be nice to lock the sim to the panel for those times I do want to pan or…

Hi all, I am very close to purchasing the RXP GTN750 for my flight sim cockpit, but i will not be using it in 3D aircraft cockpits instead I will be using my tablet as a secondary display connected to my PC and will have the GTN on there (to allow for full touch functions etc.) So firstly I'm assuming i can use it 2D style with no Garmin border with any XP 11 aircraft? Also, as using a tablet as a monitor via USB I wanted to make sure there are no compression or lag issues which may cause problems before i make the purchase. But is there any limited demonstration versions of the GTN750 available that I could test it out to ensure it works properly? Als…

I’m new to helicopters. Any issues with plugging in the GTN 750 into the ones stated in the topic? Can you use autopilot to fly an ILS approach with it? I haven’t bought the package yet and am looking to pull the trigger. Also, I guess you have to load the flight plan directly into the GTN unit. Can it read standard Xplane 11 flight plans?

Gents - I wonder if anyone can give me some advice? I'm building a PA28 home cockpit based on the vFlyteAir PA28-140 (which is about to get RXP support). The GTN750 with the touch features will save me a TON of wiring, dials, custom parts etc in building a radio panel (and without buying some very expensive 3rd party kit!!). I'm using it with XP11 and will purchase an HDMI/VGA touchscreen for the purpose, which will be connected directly to my main computer's graphics card. What I'd like to find out is - if I undock the GTN750 in a separate window in the sim and position it on the touchscreen, will it stay there? Is there a way to ensure that every tim…

Hi, greetings to all, I am new here and sadly i must report about Buying troubles with reality xp. Today i buyed a GNS 750 for xplane 11 and all is o.k. After some time today i buyed a GTN 650 in the bundle offer too. But there is an error in the buying process : I recieved a code from the 650 and in the further "complete PayPal Purchase" there allways flipps up the message : "Your Order coud not be approved because of the following reason Coupon : Reqired order number not found Please check your information and try again " I tried it some times but always flipps up the message I ha…

HI, How do I install this.

Hey my rxp gtn keeps telling contact vendor can someone help me please!!!!! how can i contact rxp or how to fix

Hello. I am having the same problem. Windows 10 latest edition. I have McAfees AV program installed. This all started after an update I downloaded a while ago. I got so frustrated a gave up on using the gtn. I would like to try this again. I just recently (yesterday) tried downloading the software from my F1 account. Before I downloaded, I turned off the McAfee firewall and scanner. I also added an exclusion for the gtn installer in the McAfee scanning section. I tried excluding some of the files that were mentioned earlier in the posts, but found that most of them (files) aren't even included in the folders. Even though I have the McAfee firewall and scanner turned off, …

Does anyone know if there are compatibility issues with the RXP 750 and Realsimgear GTN 750 running with Saitek switch panels? The Realsimgear GTN 750 page had a review (November 2, 2020) stating they were not able to get the GTN 750 to work with the Saitek switch panel and they had to return the Realsimgear product. I use the Saitek switch panels and I am trying to avoid having to return something.

My RXP GTN 750 inside my Carenado S550 looks like this as long as after some update last year, before it was showing just right. What could be causing this issue? Please help. I want to attached my log text file but I dont know how to here or should just paste like this. Spoiler Installer log.txt for X-Plane Installer 4.13r1 compiled on Jul 29 2020 09:30:51 Installer started on Fri Apr 9 08:45:57 2021 This log file is generated automatically by Laminar Research applications and contains diagnostics about your graphics hardware, installation, and any error conditions. If you need to contact tech support or file a b…

Hello to all, I wanted to modify my gtn 750 ini file to remove the red padlocks. And here is that my 2 ecran gtn 750 does not turn on anymore. So I installed the plane again, it's still the same the 2 does not turn on. I have removed the preference of xplane and GTN same does not turn on. I don't know what to do anymore?

UPDATE: Seems good now. Are there issues with the F1 service currently? I am trying to purchase the 750 from the dnloaded installer and the "Click Here To Purchase" just comes back without an error and still says "You are ready for purchase!" in green above the button. Also the "Click Here to Reinstall" btn says failure to connect. Don't want to continuously click the "Click here for Secure Purchase" for fear of multiple charges.