Flysimware Reciprocating Aircraft

Since the recent update the cheklist is missing from the Cessna 414 AW - it just returns a blank page. This is for version 3.4.4 on the Xbox MSFS 2020 update 12 I have tried deleting and re-downloading and re-installing but problem persists

Hi. The left engine just lost power at 2400ft. But its spinning outside just as much as the other one so I dont know whats going on. I have failures turned off as far as I know. I didnt run them in the red but yes, outside the green at 38 man. Any ideas?

Is anyone else seeing the Prop Sync Light not working? I am running a repaint from FS,TO

Updated to v3.4.4 and seeing some strange behavior of the AP in ALT mode (I'm using the PMS GTN750). Randomly (2-3 times in a typical 1-hour flight) the plane will suddenly pitch up from level flight, without any changes in the AP indicators, and eventually stall if I let it. If I click on the VS button at that time it will show some crazy setting, like 1800 fpm. I can re-select the altitude, dial in an appropriate VS, and she will happily return to the selected altitude ... until it happens again 15-20 minutes later. I've tired this with no other mods in the Community folder (other than the PMS 750). I've gone back to 3.4.3, the AP behaves as expected.

After updating to 3.4.4 all Control Surfaces are full deflected, but only visual. Rudder Pedals and Yoke are centerd and working normal. In Cockpit, Yoke and Rudder is centered and working normal, all Controls working (Axis And Ohs 2.8.1) .The Plane ist also flying normal. Going back to 3.4.3 solves the problem.

Hi guys. I have the Cessna 414 through the marketplace on PC. My airplane ver is 3.4.3 and is stated on the content manager as being up to date. My throttle quad - a TQ6+ - is recognised by MSFS and I cannot replicate the issue with any other GA aircraft using a MIXTURE axis. I am using the VFHub software so bypassing the axis in the sim and attempting to map the axis in sim has no difference. Both throttles and props work as expected. I can move the in game mixture levers by grabbing them with the mouse. Any ideas please on how to rectify this issue?

Hi Guys Not one of the options of Garming is working. 430, GTN750 PMS50, GTN750NXI Thanks, David

So I dunno if this is just me, or an issue with either too little flap drag or induced drag. I'm new to flying the 414 so it's probably just me, but... on final approach I want to keep it around 100-110 kias with full flaps...but the airplane takes soooo long to slow down after pulling throttles back to idle that she floats all the way down the runway. When I watch YT videos of the real plane landing they dont need to cut throttles until well over the fence in the flare...if I wait that long to cut throttles the sim plane will float a long way doing this, whereas the real one bleeds airspeed alot quicker. Seems I have to keep the plane well under 100kias on…

Landing at MRDK under the radar. I use to have this plane for FSX and now since my purchase of this plane I love it even more! Buckle up, sit back and turn up your sound for an chilling approach into MRDK. hehehe watch in 4K Link: https://youtu.be/qSbaMzC85aw

I'm curious is it just me? Downloaded v 3.3.3 this morning through MSFS Marketplace and the mixture controls are fixed at the cut off position although it's apparently possible to use a mouse thumbwheel to alter values. I deleted the first copy and tried a second time but with the same result. It's perfectly flyable if you ignore those controls and open up with engines running.

Hello! PMS GTN750 2.1.66 Payware version PMS GTN I can't see Origin bar (where set a Departure ICAO) but as I re-start simulator everythings works as should be. I found this problem a couple days ago. Has anybody been problem with PMS GTN750 as You start a sim? I set battery ON / avionics ON and wait as I could be set Departure / Destination Airport ICAO code to the GPS. About what I see is: Active Flight Plan Enroute This is Empty API Info Add Enroute Waypoin…

I have been using the C414 for quite some times now and it's probably one of my favorite aircraft for MSFS. However, I have noticed an issue when using the HDG of the AP. The plane always turn with an angle of 30° which is I think a bit to much (most of the AP I have used for GA aircraft usually maintain 20°). Does anyone have the same issue and did someone manage to fix it?

Hi, I have a ackward issue with the cabin climate (tablet). I start a flight In parking position, afterwards I load the cold and dark state and then only start both engines. Ambient temps are -5°C, cabin fans and heater are off and the cabin climate is far to the left in the yellow area as expected. After about 5min running the engines without any load the cabin temperature is in the red area beyond 32°C degrees. To my understanding either the cabin heat + fans have to be switched on or the cabin pressure system needs to be engaged with warm air from the engines to get the cabin warm or do I miss something here? Cheers, Dennis

Hello fellow simmers, I am having this issues for some time and last few updates didnt solved the problem, anybody else having the same problem like me or already solved it ? It appears like a red light that is glowing out of upper engine grill. Thanks a lot in advance for any tips.

I took a chance on the Xbox version of MSFS on my laptop, and was so pleased with the performance I was getting that I jumped right on buying the 414A, even though I missed the Thanksgiving-time sale, I still feel like it's worth every penny. Great job on this guys, it reminds me so much of flying my cousin's Ram IV Cessna 340!

To reproduce - choose PALH and water runway on world map. This is large Seaplane base in Anchorage AK These 2 items are different (incorrect) compared with start on hard surface runway. 1. Starter for left engine is on and clicking, and cannot turn off for 60 seconds 2. Fuel L/R are off and the right engine dies. Left engine continues to turn. Here is some scenery - https://flightsim.to/file/19256/palh-lake-hood-airport (not perfect) The startup at a dock is correct - everything off. Version MSFS - SU8Beta 1.23.11.0 Version G-44 1.8.1

Hey all, I've installed the 414 a few days ago, updated it to the latest version, and noticed 2 bugs that are a bit annoying (1 more than the other). The first bug is that my pilot is stuck as a female. I don't really mind, she has a nice voice. The more annoying bug is that ATC is greyed out after giving me a squawk code and me acknowledging it. It only happens in the 414. I tried other airplanes and none have that problem. I can't do anything after that. I tried manually switching to another radio, but it forces me to choose "Boston center" or "Montreal Center" and then nothing happens. I uninstalled the plane and reinstalled it to no avail.

Im not getting any response from the RN-107A Light blinks but no dme or obs or audio frequency good in garmin im running ils dme and need two navs working at the same time.

Hi, is it possible to load a previously saved flight, e.g. in cruise, through the MSFS menu?

I made a short flight this afternoon with this new version and had a defective AP: No indication of VS when pressed (and not functional either), no indication other than GPS on the screen, but yet, the plane would not follow the GPS route with precision, only when I pressed NAV again did the plane come back on the route (hence the screen indication is not reliable. I also tried the climb with IAS but no indication again on the screen. Although my altitude of 11000 ft was correctly selected, the climb stopped at 10300 ft and I had to intervene manually to get to my FL: Since I never had these issues before, I wonder if something has not gone wrong in this version, or am I …

Hi there, i have a problem. The Navigation Instruments just show white as i switch them on. Reinstall has no effect. Any help would be appreciated. Grumman 44 was bought a year ago via MSFS Marketplace. I did not play since 6 Month and before it worked fine. regards Mike Picture of problem https://ibb.co/9t9KgmW

Hi guys! I finally get my MSFS to work and first plane I absolutely wanted is this beautiful baby. I did a flight today with the last build and I noticed that the 3 landing gear lights are not illuminated with power on of course! Did I forget something ? Apart from that it's a pure marvel and a dream to fly, kudos Flysimware👋! Cheers Pat

I'm having trouble with the cabin heater (the gasoline heater, not the engine heat exchangers). More specifically, it doesn't seem to work. Doesn't matter if engines are running or not, it doesn't make the cabin warmer. I made sure to turn it on, battery on, airflow knobs pulled out, heater rheostat (knob under the defrost lever) turned all the way over. Turned the cabin fans on (tried it with them off, too). I can get the cabin warmed up with the engines running and their heat exchangers turned up, but not the cabin heater. Anyone else have this issue? Is it a known issue I missed?

Hello! I just bought it and installed it. I click over the upper triangle glass part as seen in videos (no click spot in the manual shown) and it does nothing. I don't have EFB. Please help.

ALT Alert Light on the panel next to the AP Light Doesn't seem to work now after last 2 updates.