Little Navmap | Little Navconnect | Little Logbook Support Forum

it would be nice to have a dialog box for /View/Airspaces. at present, each time we make a selection the menu closes and we must start again.

Hi Alex I found a mistake in the german translation In Einstelluingen / Kartenanzeige 2 / Nutzerflugzeug / the "Indicated Altitude" is translated to "Angezeigte Luftgeschwindigkeit"

Trying to update the AIRAC to 2012 for Little Nav Map ~~~ There used to be two buttons to download either a 'native' version - or - 'other' (can't remember what it was called)... On the Navigraph site today there are THREE buttons for download but NO indication of what they are for! Any ideas? I have posted on their support forum but in the past have not been too enamoured with the rate of reply (if at all).

I am noticing the flight plan looks a bit different when loading it from an MSFS PLN file that I exported with LNM verses manually creating it from inside the TBM 930. When loading in the flight plan file it doesn't seem to show the SID and STAR sections. But they'll show if I manually create the flight plan. Could there be some sort of bug with the export MSFS flight plan feature in LNM where it's not properly tagging the SID and STAR? In this picture below, I created the flight plan manually from inside the TBM's cockpit and chose my SID/STAR, and it clearly shows (circled in red) where the SID and STAR sections are in the flight plan. But if I load the…

When taxiing and flying, LittleNavMap sometimes autozooms/autocenters which is quite disconcerting when you were trying to see something else on the map or at a diff zoom; I am sure this is configurable but I haven't been able to see where?

I am using the latest LNM 2.6.3 beta and have noticed that the altitudes calculated by LNM do not match up with the one's shown in MSFS. I have posted a screenshot of the issue. I have created the flight plan in LNM and have exported to MSFS PLN format and then loaded it into the sim. Shouldn't it be reading the altitude data from the exported plan file that LNM created?

Can LNM be setup with a Mapbox map and if so, how? Thanks, JJ

I have downloaded these files: MSFS Tutorial IFR Bembridge (EGHJ) to Wick (EGPC).pln and Tutorial IFR Bembridge (EGHJ) to Wick (EGPC).lnmpln But the runway at EGHJ is very short, I can barely take off so how am I suppose to create an aircraft profile for this plane? I managed to take off but way earlier then norm. I rotated at about 115kts and had to pull up in order to clear the trees at the end of the runway. set my initial climb to FL300 for my cruise altitude, not sure if thats right. Getting errors in LNM complaining that 24500 ft is the max or something. But anyways. I'm not sure if I am suppose to fly the entire route? In LNM it says the route is 538…

With flight planners such as PFPX and SimBrief, there's an option to print out or save to pdf your flight plan. Would love to see this feature being implemented into LNM. Would it be possible for you to add that in?

Hi Alex, thanks again for continuing to develop this beautiful program .. I wanted to ask you for advice, I connected the laptop remotely with f s2020, the plane is in position but the route I had developed in the host is not visible. tell me where am I wrong?

Little NavMap 2.6.2 beta. In a user defined approach, the X-Plane exported flight plan shows the same coordinates for the initial fix and the runway threshold.

As the title indicates I want to exclude the ICAOregion from every waypoint. Is this possible? The workaround now is to manually delete it using a text editor.

Hi, thanks for creating awesome software. The Fuel at Destination number on the Fuel Report, when is it calculated? Is it recalculated during flight based on the fuel flow from the aircraft? And if not, is there a way to estimate the remaining fuel at the destination based on LNM data? Thx again.

Hi, I was running ver:2.62 of LNM with no issues until I updated MSFS2020 last night. When I try and launch LNM I get the following message. littlenavmap has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you when a solution is available. I have tried uninstalling LNM and re-installing it again. I have tried going back to ver 2.6.1 but I still get the same message. Thanks

Is there a way to only scan addon airports when updating the scenery library? I know the MSFS database hasn't changed, but I may have added a few addon airports, and would like them to be included in the database as well, but right now that means scanning everything (and that takes a while...)

Is there somewhere in LNM that it shows us what my local times ETA is currently? The final destination time using my computers local time and a flight plans estimated time is what I am after. That way I can set the AP and go do some chores if I know that I can leave the flight deck unattended. Then come back to the flight 20 minutes prior to landing. An MSFS, non-live users session, of course! :)

Hi Alex, Is it possible ? I couldn't find a way. This is mainly VFR thing in which although the flight altitude can be set for the entire flight, sometimes each leg needs to follow a specific max/min altitude (due to scenery, or height restrictions), this can really be great if in the edit waypoint dialog, I could enter desired height, which will show up in the legs grid and printable flight plan. Thanks, Doron.

Hi Alex, It has been suggested that I provide a link here. https://forums.flightsimulator.com/t/little-nav-map-to-get-a-name-change/308225?u=captainlif

Hi Alex. How can I both maintain a zoom level and keep the aircraft centred on map (in flight).

Hi Alex, I came across https://www.navplan.ch/ which allows you to plan VFR flight. It has a very cool feature that really helps one plan a VFR and verify you do not cross un-wanted CTRs, TMA and other airspaces. In the Fl https://drive.google.com/file/d/1b0yZoE49ZP6IsTyISq5-0kcPjteYIKsy/view?usp=sharing ight plan elevation profile, it also show which TMAs / CTRs the leg crosses and their minimal height. This way, you can see immediately if you need to change the legs height to avoid them. Thanks, Doron.

So I'm subscribed to the Navigraph beta and have AIRAC 2011 installed but in LNM under Scenery Library it still shows Navigraph AIRAC Cycle 2010? Any ideas? Thanks EDIT: Solved! Forgot I had to update the AIRAC through the Navigraph FMS Data Manager!! All sorted

Thank you so much for this app. It works very well in XP 11 and FSX without any major issues. Is it possible for future releases to expand the map view to a full-screen layout when undocked? Currently, I have to drag and expand the edges to fit the map full screen on my second monitor.

Hi Alex, Seems like you search by the first word of a full name. Will be great if you could do that cross words. Example : Charleroi airport in Belgium. If you look that up, you won't find it. You need to do "Brussels South Charleroi" to get to it. Just a nice feature in my opinion, as a full name is rarely used. Thanks, Doron.

I've changed quite a few settings, set up some paths, etc. Whenever I download a new version will I have to redo all that work? Or is there a way to keep my options?

Hi Alex, Is there a setting to increase the map brightness in night mode? I'm using the Google satellite map but it is too dark and hard to read. Thanks.