vonmar

MSFS2020-Longitude-Panning-ok Quick test screenshots during Chart panning (joystick): Edit: Just to verify if you are using LOCK or Legacy in Cockpit Interactions: I use LEGACY.

You are welcome. Remove your old Navigraph cycle (your mismatch problem) to use the default MSFS data:

If your are selecting Navigraph Navdata for MSFS you get the Navdata (sub) cycle your paid for.

All ok using MSFS2020/Navigraph KHKY ILS24 SANFI transition:

Additional information. Page 18 of the Flightfx Citation X manual gives a link to their tutorial video: https://www.youtube.com/watch?v=Uer2j267z08 Speeds and altitudes that are part of the e.g., SID/STAR/APPROACH will be shown in the FMS. You can hand enter data for other user or ATC assigned speed/altitude for other route waypoints.

Great video. Great content. You are correct on all points mentioned in the video. “Flight Simulation Is Becoming Too Expensive ?” Yes. My two PC’s (5 and 6 years old and $3000 USD each) are OK for: FSX, P3D 4,5,6, XP11, Xp12, MSFS2020 all currently used for my training flights. My next PC because the current ones are old enough for the bin would be right at $5000 USD. So then when I get a new PC $5000 PC I can then Add $$$? for MSFS2024 + new aircraft, airports and add-on software for it. Currently in a holding pattern on a new PC and MSFS2024. Note: I seldom fly any of the included default MSFS2020 aircraft.

The Beechcraft Bonanza G36 does not have rudder trim.

Ok, great. You have a working Elevator trim. Do not worry about outside view. We are not flying and testing right now. It does move very slowly. Did you test Elevator and Aileron trim wheel movement with just the mouse and not Yoke buttons?

Beech G36 Aileron Trim is present and is working in MSFS (screenshot). Have you tested to see if it is moving (turning CW/CCW) on command in your setup? This is only a 30 second test prior to taxi or takeoff. Note: There is also an Elevator trim wheel. Is it turning on command in your setup? Edit: Both trims must be checked for correct setting prior to takeoff.

Did you check the MSFS's Bonanza G36 Aileron trim wheel as I previously mentioned?

I tested the Bonanza G36 aileron trim and it is working (MSFS2020). I have the trim assigned in FSUIPC and in MSFS2020 while using Saitek Yoke buttons. If you manually use the trim wheel and mouse button in the VC cockpit does the aileron trim wheel move? Edit: Mouse select CW or CCW arrow then Clicking or holding the L mouse button? In Bonanza only the Left mouse button is used on my testing. If you use your assigned yoke buttons does the trim wheel move? Clicking or holding the assigned L/R button down?

While hand flying are you correcting for roll? Which aircraft are you flying?

Thanks for confirming.

Just had the PMDG777-200LR (2.00.130) freeze up just before selecting (Perf Init) ZFW LSK. Nothing working in the VC cockpit except a few lighting knobs could be rotated. Had to exit MSFS2020 version 1.39.12.0.

This Chaseplane Update is only for MSFS2024.

MSFS2020 FSUIPC Navigraph Charts Note: I tried Chaseplane but found many problems with my 2 monitor setup. So, I uninstalled it.

A screenshot or short video of what you see would be helpful. Does it look like this?

Scott, Thanks for the additional Discord/Product download information. I have been using version RTMM v1.1 (2 Zip files for MSFS2020) since 2021. Currently reviewing the information in the RTMM forum.

I use MSFS2020 and my RTMM is old version 1.1 Is the updated RTMM for MSFS2020 and MSFS2024? Note: I am not on their Discord Server.

"Where roughly in the world are you?" I was quoting you and I answered your question.

The airport the OP mentioned in the first post is: (Split airport RWY 05) The same as I used in my screenshots.

Just did a quick test. MSFS2020 PG On and Off (screenshots). Notes: I never purchased MSFS2024. I have an older PC (2019) and normally have PG Off. New PC would be about $5000 US. For my setup I am satisfied with MSFS2020. I have purchased a helicopter and several aircraft. Some of my MSFS2020 Addons have not been updated for MSFS2024.

You could do a short video.

Testing Chaseplane 1.0.20 P3D Personal 6.1.11.31619 FSUIPC 6.2.2 Two monitor setup WIN11 I noticed problems when using keyboard keys for: Brakes/parking brake. FSUIPC button assignment for parking brake (Saitek Throttles). L key for landing lights. Once Chaseplane Interface is selected (in focus) the keyboard keys and button assignment no longer work. If I click on the main monitor (so in focus now) keyboard keys and button assignments are now ok. Also, the Chaseplane Interface will expose otherwise hidden selection elements when it is in focus and keyboard keys are in use: Ctrl (tap it) Ctrl (hold it down) Ctrl + . (period) FSUIPC button assignment for parking brake Are other pilots with Chaseplane, P3D6 and a 2 monitor setup seeing the same problems? Short video of what is going on on my setup. https://youtu.be/3fFyr_jQKPY

Thanks for retesting and confirming the original problem has returned. I see Chaseplane problems with P3D4, P3D5 and MSFS2020. P3D6.1 is looking good but limited testing. Edit: Chaseplane and FSX (Steam) on a 2nd two monitor PC with WIN11 also looking gods