December 30, 2025Dec 30 How do you set the trim? Nothing I do changes the position of the little green arrows on the trim indicator. Tom
December 31, 2025Dec 31 Where did you set your trim up? In MSFS or in an external utility (FSUIPC7, Axis and Ohs, etc)? Best regards, Luis Hernández Main rig: self built, AMD Ryzen 7 5700X3D (with SMT off and CO -50 mV), 2x16 GB DDR4-3200 RAM, Nvidia RTX 5060Ti 16GB, 256 GB M.2 SSD (OS+apps) + 2x1 TB SATA III SSD (sims) + 1 TB 7200 rpm HDD (storage), ID-Cooling SE-224-XTS air cooler, Viewsonic VX2458-MHD 1920x1080@120-144 Hz (G-sync compatible), Windows 11. Running P3D v5.4 (with v4.5 scenery objects as an additional library, just in case), FSX-SE, MSFS2020, MSFS2024 and even FS9. XP11 and 12 installed, just for curiosity. Mobile rig: ASUS Zenbook UM425QA (AMD Ryzen 7 5800H APU @3.2 GHz and boost disabled, 1 TB M.2 SSD, 16 GB RAM, Windows 11 Pro). Running FS9 there for airliner ops. FSX-SE also installed, just in case. Lossless Scaling in al my rigs. What a godsend... VKB Gladiator NXT Premium Left + GNX THQ as primary controllers. Xbox Series X|S wireless controller as standby/mobile.
December 31, 2025Dec 31 Author I think I got it under control. Man, does the trim move slowly. Is there any setting to speed it up? Edited December 31, 2025Dec 31 by tjrush Tom
December 31, 2025Dec 31 1 hour ago, tjrush said: I think I got it under control. Man, does the trim move slowly. Is there any setting to speed it up? I was just about to post to say that it does move.... but darn it's slow! 😄 Worth noting that correct elevator trim for TO in the PC-12 tends to be a few degrees nose down. Definitely don't want nose up trim in this aircraft as nose down trim sets it up for initial climb out at published speeds. If you take off with nose up trim in the PC12 you'll be pushing the trim down hard while sweating, once you're above 200' 😆 Bill 😎 FS2024 • PMDG 738, 777F & 777-200LR • Fenix A319, A320, A321 • TFDi MD-11 • AS/ToLiss A346 • iFly 737 MAX8 • Ini A340 • AS CRJ v2 • Ini A300 Premium • FSS 727F • FFX HJET, Visionjet and P180 2024 • A2A Comanche 2024 & Aerostar • All BLACKSQUARE aircraft • COWS DA40 & DA42 • FSW C24R Sierra & C414 TrackIR • BeyondATC • PMS GTN Payware • RealTurb • Axis & Ohs • FS Realistic Pro 9800X3D • RTX 3080 • 64GB DDR5-6000 NPPL licence holder in the UK
January 2Jan 2 I use - Lorby's Axis And Ohs - for various settings in the SWS PC12 and for the Elevator Trim I set the parameter for it at 15000 or -15000 for trim up and down which is also multiplied by the 'Roll' figure which I've set at 9 , I find this gives a good speed .... ... figures can be seen in the top right of the floating panel in the pic https://i.gyazo.com/73898fbf453bdf5f785008a7757f9c4e.png Edited January 2Jan 2 by aerostar
Create an account or sign in to comment