Bravo Throttle Quadrant Support

This section is for the Bravo Throttle Quadrant. While we will strive to answer your questions in this forum, official support is done via the support ticket system on the Honeycomb website.

On my old computer, the Bravo worked fine with XPlane 12 and Zibo Mod. That computer died. With new computer and new XPlane download, my throttles jump out of position when I pull the speedbrake. Kicks off auto throttles. every time. I repeatedly calibrated them to no effect. I figured I had to update the drivers and I found them on the website, but the installer will not load them into XPlane. Does anyone have a suggestion or, is there any tech support available now?

I cannot get MSFS 2020 to recognize key assignments assigned in MSFS 2020 Brovo setup page. I can assign them but MS doesn't react to them. ex I assign throttle 1 and throttle 2 axis and assign the key above to show direction of throttle lever, and MSFS doesn't show them working. Any ideas, Jack Maxcy Ideas please. Jack

Ever since SU11 on MSFS2020, the honeycomb throttle quadrant has not worked for the default 787. I even tried to reconfigure the throttle quadrant for a Two Engine Jet, and it still does not work. It works for the Captain Sim 777 and 767, the Bredock 737 Max-8 and the Airbus 330-900. But it does not work with the 787. Has anyone experienced this?

Had major CTD issues with MSFS 2020. Through their (MS) support forum, i returned the sim to "Vanilla" state and tested. This included disconnecting all peripherals as well as removing all 3rd party software and payware from the MS Store. I was able to operate the sim properly in the vanilla state, then started reintroducing other stuff, and the last thing to restore was the Honeycomb Alpha Yoke and Bravo Quadrant. I have had these for almost as long as I have had the sim, with no problems to date. Lo, and behold! The sim crashed to desktop again. I tried different configurations: - No alpha or bravo at startup - all ok Alpha connected, no brav…

Hi, Did I miss something or is ist really so that the throttle axes do not work past the idle detent of the lever? Value is 0 at the detent, and seems not to be adjustable. If so, how would I assign a reverse axis function? My sim is MSFS, and I have not installed any specific software for the Bravo yet. Regards Boris

I am looking for an editable template for me to make into a PowerPoint to show what switches, etc. go to different aircraft.

Just got my Bravo last week and decided to profile using in sim ( P3DV5) profiles and FUSIPC. I Can’t get any input from the little red TOGA button on the number one jet lever. Does anyone know if this is a real input button or just there to be pretty. I would like to use it for its intended TOGA function but it doesn’t seem to do anything. Does it only work with the Honycomb software.

Hello all, I am getting a runtime error when I attempt to install the software drivers for the Honeycomb Bravo. This is the error: . Further information, I am running MSFS 2020 from Game Pass on my PC. Has anyone ever seen this / have a fix?

Purchased the PMDG 737 and the Function buttons do not light up when pressed. They do on the other aircraft but not on the PMDG737. I tried to run the AFS Bridge from with in the Community folder and when I try to execute it I get ": Failed to initialize SimConnect to the line." Have no idea what that's telling me. Also in MSFS content manager the AFCBridge is showing up as not installed. If I select it in the Content Manager It wont give me the option to install it from there. Kinda of hung up on this. Any help will surly be appreciated and happy flying. Thanks Walt

Does anybody know the dimensions for the BRAVO THROTTLE QUADRANT? Any comments or feedback would be appreciated! Thanks

So I ordered replacement airliner handles in on April 20th. I have emailed them back and forth on an update when it will be shipped. They are telling me that their warehouse is having issues with their printer to print shipping labels..., then they told me that it should be sent out last week....well here we go again...nothing...I have asked for a refund and they have refunded me the money and cancelled my order. They told me to order from other providers that are affiliates to them since they are having issues. Does anyone else know here I can order handles? I have searched and cant find it. "Good morning, We sincerely apologize for this inconvenience. I will cancel you…

Hey, Anyone know how to configure HC bravo for the longitude ? I set it up like every other plane but when i put full throttle it stay idle and when idle it goes reversed, not matter if i reverse the axis, Throttle 1 and 2 axis are set correctly and i use throttle 1 and 2 decrease for both reverser as usual but it doesnt work Any clue ? Thanks

I am attempting to install Software (e.g. Bravo Throttle Quadrant) into P3D v6 however I noticed that it will only load into P3d v5. Is there anyone who knows if Honeycomb will update to v6? Thanks in advance and kind regards Dirk Karmelk

Hi folks. I am just starting to look at autopilot in the sim. I wanted to ask folks with more experience than me whether the default definitions for the autopilot section on the Bravo throttle quadrant are accurate and functional? I see that all the buttons and knobs have definitions but are they correct or do they require modification to work properly? Thanks

I'm using this unit with X Plane 11. I'm fairly new to all this so take my assertions with a pinch of salt. To the best of my knowledge I am using the default setting to fly the CESSNA 172 with the G530 GPS. Various videos suggest pressing the NAV button twice to activate GPS mode but this does not work for me and I have to use my mouse instead. Pressing NAV twice on the screen works. As far as I can tell everything else runs as expected. Al

Hi, I purchased Honeycomb Bravo on December 15, 2021. Unfortunately I have a problem with thrust number 3. When I go into reserve it scratches. My question ? Do I still have a warranty? I bought it here in Germany via Alternate, or do I have to contact Honeycomb? Thanks

Hi, Can anyone tell me if the throttle has had more then one version produced. I have a deal that looks to good to be true. Makes me wonder if its not something like version 1 and we are now at version 5 or something like that. Thanks

Anyone have tips on how to get support from Honeycomb? I have a Bravo that is about 2-3 months from being out of warranty, not very heavy use, and just noticed "button 10" i.e. the Boeing style reverser switch on 3rd axis from the left or the red button on the Airbus style throttles is no longer working. Nothing seems damaged or dirty with the contact and the handles both work fine on the other axis locations. I submitted a ticket through their website a week ago and haven't heard anything back even a "we're overloaded and will get to you asap" or something. I caved and signed up for their zendesk site and saw my ticket in there and it just says "Open" with nobody ass…

I have a new Bravo so I can fly the ATR. I set it up using tutorial from SimHangar. For a couple of weeks it worked fine on the ATR. I also use it for PMDG737 and XP12 737, with profiles for each. Then on ATR, #1 throttle started moving out of Notch position, falling to flight idle. I would move Bravo to reset it, but it would quickly fall again. I yesterday tried deleting all throttle 1 assignments and reassigning them. That worked for 1 flight. Now it is either at full reverse position or full throttle. No in between. The other throttle works fine. The 737 doesn’t appear to be affected. What should I try? How can I tell the difference between a…

Hi,anyone having the landing gear not working in MSFS 2020? It's not even detected when I use it in Option-Controller.

All, I am looking for a complete set of the Bravo quadrant commercial levers. Been waiting for a while for a response from Honeycomb. Thanks Phill Dant

Just wanted to let everyone know that if you have Bravo Throttle system from Honeycomb, FlightsimFactory has creaed a set of handles for the new Microsoft ATR. Just purchased my set. Wanted to share https://www.etsy.com/listing/1474240963/new-atr-42-72-pro-throttle-detent-set?click_key=01055a50a68dab0221f6542418ec5cac7af75f98%3A1474240963&click_sum=1d0a55b5&ref=shop_home_feat_1&sts=1 Bill

This is for the Honeycomb Bravo throttle. Does anyone see the problem with the download or where it has been placed? I have been working for days trying to get these lights to work, read every article and watched every video.. This is so aggravating. Sure could use some help. Thank you!! Cindy <?xml version="1.0" encoding="WINDOWS-1252"?> -<SimBase.Document version="1,0" Type="SimConnect"> <Descr>Auto launch external applications on MSFS start</Descr> <Filename>exe.xml</Filename> <Disabled>False</Disabled> -<Launch.Addon> <Name>AFCBridge</Name&…

I recently bought MSFS 2020 (ms store) and am trying to set up my honeycomb bravo for single engine. I have watched several videos and found the one I want to follow. But I noticed something right away. In my menus, everything is reversed. For instance: throttle 2 mixture is above throttle 1, or Mixture 2 Axis is shown above Mixture 1 axis. This probably does not make any difference, but it's a bit confusing when I'm trying to follow a video which shows them the "right" way. Any suggestions on how to correct this? This is probably the first of many questions.