Hello,

 

could you please have a look into the log file and paste me any (red) error lines?

As you describe it, there's a LUA error somewhere ... but the question is: where?

 

I assume, that sth. gone probably wrong when old config files have been copied over.

So, we could test this, if you please delete (backup) all cfg files and make some assignments just for testing.

And, important question: do you have MCP1 or MCP2 or MCPa???

 

 

Problem is, on my side, everything is working, even the functions you all mention. 😯

Edited November 11, 20196 yr by guenseli

I'm currently using the Airbus FCU, but I have both the MCP1 and 2. My MCP2 is C.rap the encoders are buggy. I had a new board put in my MCP1 and that is much better, but I still have my FCU bolted into my cockpit at the moment. I'll try what you suggested above first and then dig out the MCP1 later.

Edited November 11, 20196 yr by Andydigital

OK now its working, I deleted the old NGX profile and the new NGXu profile, then imported a fresh download of the module. I also didn't not copy across my settings, previously you mentioned that this would be ok, but perhaps its not.

Ok, in my case it has worked flawlessly, but I will change the initial post about it.

Sorry for the trouble

For test purposes I turned off my MCP2 leaving just my Thrustmaster HOTAS and two assignments:

Assigned: Joystick switch 20 NGX APU on and switch 21 NGX APU start

I then started the sim and then LINDA.  I stopped the Logging Session after a number of errors printed all the same.  Here's a partial copy:

------------ NEW LOGGING SESSION - LINDA 3.0.12.811 --------------

LUA: "D:\Program Files\Lockheed Martin\Prepar3D v4\Modules\linda/system/init.lua": killed

### Blocked: attempt made to change LogOptions via 3400, data 0x0001

FSUIPC logging bit cleared: 2

### Blocked: attempt made to change LogOptions via 3400, data 0x0401

FSUIPC logging bit set: 10

### Blocked: attempt made to change LogOptions via 3400, data 0x0001

FSUIPC logging bit cleared: 6

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

[E] *** LUA Error: ...D v4\modules\linda/aircrafts/PMDG 737NGX/actions.lua:344: attempt to compare nil with number

Please ignore the strike through lines.  I don't know how or why they are there in the post.  They do not

appear in the raw copy.

Phil

Edited November 11, 20196 yr by UAL066

It's more likely its something I did wrong, but it's working now, so thanks again for all the hard work you folk do with Linda, the hobby just wouldn't be as good without you.

The Recall button doesn't work, it seems to get stuck in the pressed state, i.e. how you test the lights behind the button. While pressed they should all light and then go out after release, as long as they aren't still in a caution state. For me though If I press it through Linda it stays stuck in the test state even though the actual animation shows it being released.

29 minutes ago, UAL066 said:

modules\linda/aircrafts/PMDG 737NGX/actions.lua:344:

 

You do not use the NGXu module!

Try to delete everything in the Prepar3D v4\Modules\linda-cfg\aircrafts\PMDG 737 NGXu folder (backup!) and try to assign something for testing

2 minutes ago, Andydigital said:

The Recall button doesn't work

 

ok, will have a look

Ok, regarding the Recall Button, I have found a fix.

 

 

It seems, the function itself in the NGXu is broken as you can press the button, but it's going released despite you still hold the mouse. I can't change this behave.

 

But it works now with LINDA in the same as if you press with the mouse.

Will update the module now in a few minutes

Nice, looking forward to the update.  I've noticed also that the ground options section, like connecting the GPU and Air doesn't work either.

5 minutes ago, Andydigital said:

 I've noticed also that the ground options section, like connecting the GPU and Air doesn't work either.

 

Yes, noticed that, too. Will have a look.

For now, v1.1 is online

2 hours ago, guenseli said:

Yes, noticed that, too. Will have a look.

 

Done, module 1.2 online

Lol, nice work. Who's online all the time now?
 

Just a minor point but the readme file still mentions 1.1 so when you import Linda thinks its 1.1 still. I know it probably makes no difference but though I'd just mention it.