May 28, 20197 yr When on a flight on FSX and I am taxiing and use my brakes on my rudder pedals the brake notification on the bottom left side stays applied. I have to use my CTRL key and my period key to cancel the brakes. Just wanted to know if anyone else has had this problem. If so what did you do to correct the problem. It used to be that when I used my brakes on the rudder pedals the message about brakes being applied would go off after releasing the rudder pedal brakes. As of now it does not and I have to use the keys to cancel the brake being applied message. Any info on this would be a great help to me. Thanks for your info and help in resolving this issue. Duane R.
May 28, 20197 yr Usually that's because your brake axes are reversed. Initially, the brakes are off because they default to off initially, and until you make an input on the axis the brakes remain off. Then when you first apply brakes you are actually progressively releasing them, and when you get off the pedals you end up with full brakes. Go into the Controls menu and tick the "reverse" checkbox for your brake axis and see if that fixes it. Regards Bob Scott | President and CEO, AVSIM Inc ATP Gulfstream II-III-IV-V Sys1 (MSFS20+24/XPlane12+11): AMD 9800X3D, water 2x240mm, MSI MPG X670E Carbon, 64GB GSkill 6000/30, nVidia RTX4090FE Alienware AW3821DW 38" 21:9 GSync, 2x4TB Crucial T705 PCIe5 + 2x2TB Samsung 990 SSD, EVGA 1000P2 PSU, 12.9" iPad Pro Thrustmaster TCA Boeing Yoke, TCA Airbus Sidestick, Twin TCA Airbus Throttle quads, PFC Cirrus Pedals, Coolermaster HAF932 case Sys2 (P3Dv5/v4): i9-13900KS, water 2x360mm, ASUS Z790 Hero, 32GB GSkill 7800MHz CAS36, ASUS RTX4090 Samsung 55" JS8500 4K TV@60Hz, 3x 2TB WD SN850X 1x 4TB Crucial P3 M.2 NVME SSD, EVGA 1600T2 PSU Fiber link to Yamaha RX-V467 Home Theater Receiver, Polk/Klipsch 6" bookshelf speakers, Polk 12" subwoofer, 12.9" iPad Pro PFC yoke/throttle quad/pedals with custom Hall sensor retrofit, Thermaltake View 71 case, Stream Deck XL button box Sys3 (DCS/P3Dv4/ATS/ETS): AMD 7800X3D, MSI MPG X870E Carbon, Noctua NH-D15S, 64GB GSkill 6000/30, EVGA RTX3090 Alienware AW3420DW 34" 21:9 GSync, Corsair HX1000i PSU, 4TB Crucial T705 PCIe5 + 2TB Samsung 970Evo Plus, TM TCA Officer Pack, Saitek combat pedals, TM Warthog, TM RS300 FF wheel/pedals, Coolermaster HAF XB case
May 29, 20197 yr For what it's worth, this happens to me occasionally without me changing any brake settings. I find depressing one of the brakes slightly and releasing it usually turns off the brakes on indicator. However reading the original post Ctrl+. is for the parking brake, not the normal brakes. I'm just throwing that out there. Your situation is normal for people who have brand new pedals. Consider calibrating those pedals first and then use the FSX settings for fine tuning. Sim: Prepar3D 5.2 (main) and Microsoft Flight Simulator (2020), CH Eclipse Yoke, Thrustmaster Airbus TCA Side Stick, CH Pro Throttle, CH Pro Pedals, Saitek Cessna trim wheel, TrackIR 5, SPAD.neXt running 3 Saitek Logitech panels, ButtKicker Gamer 2, Razer Naga Chroma gaming mouse System: Intel i5-10600K CPU @ 4.10 GHz, Nvidia GeForce RTX 2080 Ti, 64GB DDR4 RAM @ 4200 MHz, ASRock Z490M Pro4, 2TB Intel NVMe SSD 660p, 3 monitors
May 29, 20197 yr I used to have this problem until I calibrated my toe brakes properly. I found that the minimum number should be zero, not a negative number, which was the mistake I made! Intel I7-4770 3.4Ghz 16 Gb RAM nVidia GTX770 2Gb Windows 8.1 64 bit P3D 4.4/3.4 FSX SE
Archived
This topic is now archived and is closed to further replies.