1. When entering cold & dark mode, these switches are like this...

And when entering takeoff mode, the switches are like this...

So, can we say that for landing and takeoff, they should be set as in image 2, and for cruising, as in image 1?

2. The POH only shows the cruise performance tables, there are no climb and descent tables.

- Does anyone have the data or a POH that includes this information?

- This label appears on the dashboard, I guess these would be the climb tables.

I am leaving the pdf, I hope someone can help me add the missing procedures.

Checklist C337

1. In the "BEFORE STARTING ENGINES" section (the CARENADO lists); there is an item that says "All Press-to-Test Lights — CHECK."

What should be checked there?

2. In the section "STARTING ENGINES." the item "Throttle - ADVANCE to obtain 60 lbs. /hr. fuel flow; then RETARD to IDLE."

The fuel flow indicator needle does not move, it stays at zero.

3. In the section "BEFORE TAKE-OFF" the item "b. Propellers -- CHECK feathering to 1200 RPM; return promptly to HIGH RPM (full forward)".

The RPM indicator stays at 2800 RPM and does not drop to 1200 RPM, even at idle speed.

4. The autopilot when activated, the nose points downwards losing altitude to such an extent that the plane crashes against the ground and no matter how hard I pull the joystick to raise it, I can't. The solution for now is to keep that setting on the knob, even so it does a minimal nose down but then it resumes altitude.

The solution for now is to keep this setting on that knob, it still makes a minimal nose down but then resumes altitude.

after setup my pc again i had to reinstall all pieces fpr P3DV5.2.

Skymaster and other planes are not working with the newest GTN Trainer which downloaded by the F1 Agent.

Who can help to find the last working Trainer?

Zhx for your kindness help

regards

Dieter 

I want to use two switches for starting the engines via FSUIPC. Here is what's working:

Magneto1 Left

Magnet02 Left

Magneto1 Right

Magneto2 Right

Magneto1 Both

Magneto2 Both

Then, Magneto1 Start and Magneto2 Start is not working. Magneto Start works but starts both engines simultaneously.

Anyone knows what to do?

Thank you,

Karl

Here's one I made earlier.

Real one:

Mine:

The interior has been replicated (as best I can) in red.

Available on my Mediafire HERE now, or on AVSIM library soonish.

Lewis Block

Regards

Pascal

FSLSpotlights is a free application that FSLabs incorporated in their Airbus and made available for free to the public as donation ware (since v2.0.0.9). It works with P3d V4.1 and more.

It allows creating a group of small lights in the VC that can provide dim (or bright) lighting to various part of the panel.

I used it to put a dim bluish light (to keep the existing mood of the C337 panel lighting) on the switches, Collins Radio Knobs, autopilot and compass so they are easier to read and operates at night.

Installation:

• You need to download and install Spotlights from FlighSimLabs web site under the “tool” menu item. Don’t worry about the price shown, it’s free now. There is some information on the page also about the app.
• Then drop the spotlight file (FSLSpotLights.ini) in the aircraft menu of P3D. Same place as you find the aircraft.cfg file. For those registered on the FSLabs forum, you can go the the FSL Spotlights section and search for the thread named “Carenado C337 Skymaster”. If not registered on FSLabs, just drop me a PM.

Operation:

• FSLSpotlights will put a small contextual menu on the bottom left of your P3D screen (a very small square). It’s described on the product page.
• You can use this menu to put this lighting ON or OFF or to modify the dim level

Limitation:

• You cannot operate those lights with a VC switch, you have to use the FSLSpotlights menu to put them ON or OFF.

Happy dark sky flying…!!

I just noticed this evening that I cannot see the rotating prop of the c337 at all. I would think you would be able to see, especially with RPM changes. I do see it when the engine is not running.

Can anyone else confirm.

thanks.

• The GTN bezel is completely black
• The ADF frequency swap doesn't work
• Cowl Flaps are toggle (temporarily hold) up and down electrical switches
• The RPM tooltips shows Fuel Flow
• The FFF tooltips shows RPM
• The Ldg Light switch is labeled "LOG"
• The "Push to Set Card" on the non-slaved HSI is not working
• Where is the "Step" button on the EDM so we can "pause" the cycling through the cylinders to make a lean procedure? Cycling it forever makes it unusable. This shouldn't be complicated to implement.
• * Landing lights and dome lights are not working (Not illuminating anything)

Also I wonder if anyone has a fix for the brake sound.  When stopping you get a brake squeal sound, but if you hold the brakes that sound gets repeated over and over again.  Very annoying when doing things like holding short.

Scott

The Carenado C337 Skymaster is my favorite aircraft, I have always flown during daylight hours but lately I have been doing some dusk and night flying.

I notice that the cabin lights are non existent and it is impossible to find the various switches on the panel. I also notice that the taxi and landing lights do not illuminate the ground.

I have tried several different airports and the problem is the same. 
But all other aircraft do not have this problem nor does this problem occur with the same C337 aircraft in FSX-SE.

I uninstalled and re-installed this aircraft but that did not make a difference.
I have made many different adjustments to the P3D settings but nothing changes.
I uninstalled my TOGA-EnvShader but that did not make a difference.

I will attached a few images - I don't seem to be able to embed the images in as Google Photos does not provide a BBCode link.

https://photos.app.goo.gl/6Reki03RFsUl373p1

https://photos.app.goo.gl/BxjYRUEc7R3nGQUG2

https://photos.app.goo.gl/aFvKSMjOfjiRRzN03

https://photos.app.goo.gl/0BAiHry6RREAkNJ42

Thanks.

I recently bought the updated Cessna 337 and found out the GPS does not popup with a mouse click, something I believe the 2011 version did. The manual also mentions the fact. I contacted Carenado support asking if only the Shift+1 key would work, and also pointed to the fact that the two lower buttons on the GPS have text inverted and the only reply I got was this:

Sadly there's no other way to pop up the GPS in the C337.

Does anyone remember if the GPS opened with a mouse click ? I believe so, as that's how I remember it worked, and the manual does say so. Any help on this?

thanks Peter

Thanks.

Changelog:
- Internal and external lights corrected
- Now reads LDG instead of LOG
- Tooltips adjusted
- Now lights illuminates the ground
- Fixes a problem that causes trim indication to disappear on GTN version
- ADF issue (GTN version only) fixed
- Door texture (GTN version) corrected.

Until Carenado releases a fix, you can edit the panel.cfg file:

[Vcockpit01]
Background_color=0,0,0
size_mm=512,512
visible=1
pixel_size=1024,1024
texture=$RadiosC337_N

gauge00=RadioC337XML!Radio_AudioCollins,  0,0,292,65
gauge01=RadioC337XML!Radio_Collins_NAV_COM,  0,180,291,115
gauge02=RadioC337XML!RadioTransVC,  0,370,300,74
gauge03=CCTTS!DME_screen,  0,68,268,108
gauge04=GAUGEC337!Radio_KR87_ADF,  0,294,300,75
gauge05=CCTTS!GEM6,  297,0,214,211

My upload of the Maintenance Pack for the Carenado C337H Skymaster has been accepted and is now available in the AVSIM Library.

Edit: The old version has been removed. Please look at later posts to find updated versions.

It currently includes the following modifications:

Cessna337_1_C.bmp, Cessna337_1_C_night.bmp:
  The label for the landing light switch is changed from "LOG" to "LDG".

Cessna337_3_C_night.bmp:
  The labels for the Prop Synchrophaser were displayed twice with a
  small offset when the panel light was enabled. The modification
  corrects this and adds illumination for the label "Phasing".

Gauges_337B.bmp, Gauges_337B_night.bmp:
  The right Collins gauge (NAV2) is now correctly labeled "Nav" instead
  of "Comm". Thanks to Bert Pieké for the inspiration by providing an
  earlier fix. I recreated his fix from scratch and added improved night
  lighting.

Gauges_337BXP.bmp, Gauges_337BXP_night.bmp:
  Same as above modification for the right Collins gauge, but with
  textures for the Reality XP GNS.

Please download the file and look at the included README.txt for installation instructions. Or you can use the ZipDive feature of the AVSIM Library to read it before downloading, or to view some before and after screenshots like this one:

Some background information:

I used DXTbmp to extract the bitmaps from the files I wanted to modify into a file named norm.bmp, then I used Gimp to edit them.

When exporting them from Gimp as norm.bmp again, I had to select "Do not write color space information" in the "Compatibility Options", and "24 bits: R8 G8 B8" in the "Advanced Options".

After reloading norm.bmp in DXTbmp, I had to disable "Include when saving" in the MipMaps box before saving them.

I hope this will bring you some additional joy when flying this already nice aircraft.

Regards,

Thomas

FREE update for a download you purchased: Cessna C337H Skymaster HD Series FSX

I tried both my original purchase link and my account invoice but nothing to download. Anyone have any luck?

Seemed to install fine for me . . .